This Code (Part 10/Section 1) covers requirements of landscape planning, design and development with the view to promoting quality of outdoor built and natural environments and the protection of land and its resources.
BUREAU OF INDIAN STANDARDS
look Supply Bureau Under the License from BIS for LARSEN AND TOUBRO CONSTRUCTION - MANAPAKKAM, CHENNAI ON 17-03-2017 09:00:59 (123.63.24.35) valid up
This Code (Part 10/Section 1) covers provisions relating to landscape planning, design and development with the aim of improving quality of outdoor built environment and protection of the land and its resources.
This Part of the Code was first published in 1970 and subsequently revised in 1983 and 2005. This Part earlier covered provisions relating to only signs and outdoor display structures. With growing urban development and environmental degradation, it had become imperative to determine landscape design parameters, and also provide rules, regulations, controls and procedures for the protection, preservation and modification of surrounding environment. In the last revision of 2005, this Part was, therefore, sub-divided into two sections as follows, by including a new section relating to landscaping:
Section 1 Landscape planning and design
Signs and outdoor display structures
The components of landscape design and external development were earlier covered in the Code in its various Parts/Sections but a comprehensive treatment was given in this new Section in the last revision only. A brief clause on street furniture was also introduced in this Section in the last revision.
In this revision, the Section is now called, Section 1 Landscape planning, design and development, and accordingly various provisions have been detailed to cover relevant aspects relating to overall landscape planning, design and development. In this revision, the following modifications have been incorporated:
a) Certain terminologies have been included/modified in view of the inclusion of above mentioned provisions and technological advancements in this field.
b) A new clause relating to landscape site planning requirements has been included.
c) A new clause covering in detailed guidelines relating to general development of landscapes has been included.
d) A new clause relating to roof landscape has been added.
e) Provisions relating to earth slopes and their grading have been shifted and now covered under the clause on statutory approvals.
f) New provisions related to materials and finishes plan have been included as part of the landscape development documents required for statutory approvals.
g) Provisions relating to paved surfaces in external areas have been shifted and now included under general development of landscapes for logical sequencing.
h) Lists of various plant species for different applications have been updated under various clauses.
The work of landscape planning, design and development is to be carried out by professionals in accordance with their qualification and competence given in Part 2 ‘Administration’ of the Code keeping in view the provisions of this Section.
For the purpose of this Section, the following definitions shall apply.
2.1 Avenue — A wide road or pathway lined with trees on either side.
2.2 Buffer — The use of landscape elements to reduce or curtail view, sound or dust with plants or earth berms, wall etc.
2.3 Canopy/Tree canopy — The average horizontal spread of the tree, taken from dripline to dripline.
2.4 Climber — A woody or herbaceous plant which either clings to a wall, trellis or other structures or can be supported or trained as it grows.
NOTE — It is sometimes also called creeper or vine.
2.5 Columnar — A slender, upright plant form.
2.6 Contour — The form of the land, existing or proposed; a part of the topography, indicated by map lines at intervals, to understand the landform clearly. The contour line is imaginary and indicates continuous elevation above mean sea level or an assumed datum line.
2.7 Contour Interval — The difference in elevation or the vertical distance measured between consecutive contour lines.
2.8 Drainage — Drainage is the natural or artificial removal of surface and subsurface water from an area through use of vegetated/open channel, pipes, drain boards, chambers, etc.
2.9 Egress — A way out, or exit.
2.10 Elevation — A contour line or notation of relative altitude with respect to a benchmark, useful in plotting existing or proposed feature.
2.11 Erosion — Wearing away of soils, rocks, sediments, etc, by gradual action of natural processes (such as water, wind and glacier).
2.12 Exotic — A plant that is not native to the area in which it is planted.
2.13 Fence — A barrier of plant or construction material used to define the boundary of an area and to restrict visual and/or physical access.
2.14 Foliage — The collective leaves of a plant or plants.
2.15 Geogrid — A deformed or non-deformed netlike polymeric material used with foundation, soil, rock, earth, or any other geotechnical engineering-related material as an integral part of the human made project structure or system.
2.16 Geo-Textile — Any permeable textile or fabric (natural or synthetic) used to retain or protect soil and filter and drain water as an integral part of project, structure or system such as terrace garden, etc.
2.17 Girth of Tree — Girth is a measurement of the circumference of the trunk of a tree, measured perpendicular to the axis of the trunk. It is measured at breast height (1.4 m above ground level).
2.18 Grade — The slope or lay of the land as indicated by a related series of elevations.
2.18.1 Natural Grade — Grade consisting of contours of unmodified natural landform.
2.18.2 Finished Grade — Grade accomplished after landscape features are installed and completed as shown on plan as proposed contours or spot levels.
2.19 Gradient — The degree of slope of a pipe invert or road or land surface. The gradient is a measure of the slope height as related to the length. The slope is expressed in terms of percentage or ratio.
2.20 Grading — The cutting and/or filling of earth to establish finished contours.
NOTE — Grading facilitates good drainage and shapes land to suit the intent.
2.21 Grasses — Plants that characteristically have joint stems, sheaths and narrow blades (leaves).
2.22 Grass Paver — Grass paver is a permeable structural grid cellular system (concrete, HDPE or any other polymer) for containing and stabilizing gravel or turf.
2.23 Green Roof — A roof surface of a building that is partially or completely covered with a growing medium and vegetation. Green roofs can be deep (intensive) or shallow (extensive).
NOTE — Intensive green roofs are elevated greens which can sustain shrubs, trees, walkways and benches with their complex structural support, irrigation, drainage and root protection layers. Extensive green roofs are shallow, relatively light and are solely used for their environmental benefits. They support native ground cover that requires little maintenance.
2.24 Green Walls — A supporting structure completely or partially covered with vegetation which is grown with soil or growing medium. It can be either free standing or part of a structure. They include climbing plants such as vines that grow directly on the wall, or walls that comprise of modular panels, containers and an integrated irrigation system.
2.25 Ground Cover — The planting material that forms a carpet of low height.
2.26 Hard Landscape — Civil work component of landscape development such as pavements, walkways, roads, retaining walls, sculptures, street amenities, fountains and other elements of the built environment.
2.27 Hardy Plant — Plants that can withstand harsh temperature variations, harsh wind, pollution, dust, extreme soil conditions, and can tolerate either drought or flooding.
2.28 Heat Island Effect — A phenomenon in which air and surface temperature of an area are higher than nearby areas due to the replacement of natural land cover with pavement, building, and other infrastructure.
2.29 Hedge — Shrubs or trees (usually of the same species) planted closely together in a linear configuration. A hedge may be pruned to shape or allowed to grow to assume its natural shape.
2.30 Herb — A plant with a non-woody or fleshy structure. Certain herbs are highly useful for cooking or of high medicinal value.
2.31 Ingress — A way in, or entrance.
2.32 Invert — The lowest inside point of a pipe, culvert, or channel.
2.33 Irrigation — The artificial application of water, to assist in growing and maintenance of plants.
2.34 Kerb — A concrete or stone or similar hard edging along a pathway, or along a road, often constructed with a channel to guide the flow of stormwater.
2.35 Microclimate — A local atmospheric zone where the climate (temperature, humidity, wind, etc) differs from the surrounding areas. The term may refer to areas as small as a few square metres or as large as many square kilometres.
2.36 Mound — A small hill or bank of earth, developed as a characteristic feature in landscape.
2.37 Mulching — A practice of using a protective covering, usually of organic matter such as leaves, straw, placed around plants to retain moisture, improve soil conditions and prevent the growth of weeds.
2.38 Permeable Paving — Paving surfaces that reduce runoff by allowing rainwater to soak through the surface into the underlying sub-base where the water is stored temporarily before allowing it to seep into the ground or flow to the drains.
2.39 Plants — The living beings consisting of trees, shrubs, herbs, grasses, ferns, mosses, etc, typically growing in a permanent site, absorbing water and inorganic substances through their roots, and synthesizing nutrients in their leaves through the process of photosynthesis.
2.39.1 Endemic Plant — The plant which is found only in one geographic location on earth.
2.39.2 Invasive Plant — The species of plant which is not native to a specific location (an introduced species) and has a tendency to spread to a degree believed to cause damage to the environment.
2.39.3 Native Plant — A plant indigenous to a particular locale.
2.39.4 Naturalised Plant — A plant that is established as a part of the flora of a locale other than its place of origin.
2.40 Screen — A vegetative or constructed hedge or fence used to block wind, undesirable views, noise, glare and the like, as part of in landscape design; also known as ‘screen planting’ and ‘buffer plantation’ (see also 2.2).
2.41 Sediment — The product of erosion processes; the solid material, both mineral and organic, that is in suspension, is being transported or has been moved from its site of origin by air, water, gravity or ice.
2.42 Shelterbelt — Shelterbelt is usually made up of one or more rows of trees or shrubs planted in such a manner so as to provide shelter from wind, and protect soil.
2.43 Shrub — A woody plant of low to medium height, deciduous or evergreen, generally having many stems.
2.44 Soft Landscape — The natural elements in landscape design, such as plant materials and the soil itself.
2.45 Spot Elevation — In surveying and contour layout, an existing or proposed elevation of a specific point noted as a dot on the plan.
2.46 Street/Outdoor Furniture — Items of furnishing in outdoor landscape such as benches, trash receptacle signage, play equipment.
NATIONAL BUILDING CODE OF INDIA 2016
2.47 Swale — A linear wide and shallow depression used to temporarily store, route or filter runoff. A swale may be grassed or lined.
2.48 Topsoil — The uppermost layer of the soil.
2.49 Transplanting — Technique of moving a plant from the place where it is growing and replanting at another location.
2.50 Tree — A woody plant, generally taller than 2.00 m, with a well-distinguished trunk or trunks below the leaf crown.
2.50.1 Deciduous Tree — Tree that sheds all its leaves during a part of the year.
2.50.2 Evergreen Tree — Tree that remains green for most part of the year and sheds leave slowly throughout the year.
2.51 Tree Drip Line — The branch spread of a tree defined by the outermost circumference of a tree canopy where water drips onto the ground.
2.52 Tree Grate — A grille, installed at the base of a tree otherwise surrounded by pavement that allows the free passage of air, water, and nutrients to the tree root, but does not interfere with the foot traffic.
2.53 Tree/Plant Guard — The protection around a tree or plant to help prevent damage.
2.54 Xeriscape — A landscape that requires little or no irrigation or other maintenance.
The qualification and competence for carrying out the landscape planning, design and development work shall be as given in Part 2 ‘Administration’ of the Code.
For any development project for which a permit or licence or statutory approval is required, an application shall be made to the Authority on the prescribed form containing such particulars as the Authority may require. The form shall be signed by the owner and shall include the information given in 3.3. For various aspects of obtaining the permit, etc, reference shall be made to Part 2 ‘Administration’ of the Code.
The site plan to be submitted with the application for permit shall be drawn to a scale of not less than 1 in 200
for a site up to one hectare and not less than 1 in 500 for site up to 10 hectare and not less than 1 in 1 000 for site more than 10 hectare. The following information shall be provided in addition to requirements for site plan as stated in Part 2 ‘Administration’ of the Code:
a) Existing and proposed topographic contours at intervals not exceeding 500 mm and/or spot elevations as pertinent and bench mark of site with reference to the city datum relative to the mean sea level.
b) Limits of the 100 year flood plain and water surface elevation, where applicable.
c) Location of existing major physical features, such as railway track, drainage ways.
d) Location of service utilities adjacent to the project with relevant top and invert levels clearly indicated.
e) Point of egress and ingress including locations and width of road.
f) Fully dimensioned loading spaces and manoeuvring areas.
g) Parking including, location, parking spaces, size and number, and typical parking space details for both persons with disabilities and for standard spaces.
h) Circulation for vehicles, bicycle and pedestrian, including for persons with disabilities clearly identified.
j) Detail for parking areas including type of lighting, material for paving, and security rooms, rest rooms; and type of directional signage, etc.
k) Drainage system, proposed finished ground elevations and finished grades.
m) Location of proposed fire hydrant points.
n) Location of fire lanes.
p) Proposed lighting layout.
q) Landscape irrigation points and source of irrigation water.
r) Vegetation for screening by type, material, height, location, and spacing or fences, walls.
s) Location of proposed street furniture, landscape structure.
t) Refuse container location, size, and access.
u) Landscape paving materials with location.
w) Location, type, size, and height of existing and proposed signage.
y) List of existing trees with botanical and common names and height, girth, canopy of the tree and existing grade levels (see 11.1.2 for plant material schedule).
z) Prior approvals, where applicable.
The grading plan shall be drawn to a scale of not less than 1 in 200 for a site up to one hectare and not less than 1 in 500 for a site up to 10 hectare and not less than 1 in 1 000 for site more than 10 hectare. The grading plan should include measures for soil and sedimentation control and also measures during construction to prevent soil erosion, and also water harvesting practices (see also 11 and 12).
Design for changes in elevation in the outdoor environment is a primary component of landscape development. Grading of proposed external development areas should relate to the existing topography of the site and it should direct surface water runoff to the designated drainage and water harvesting area. Grading design parameters are as follows:
a) Proposed grading design should respond to the function and purpose of the activities to be accommodated within the site.
b) New development and structures to be integrated with existing landform within the site and in its immediate surroundings.
c) Stormwater to be directed away from buildings.
d) Steep slopes to be modified to minimize or eliminate erosion.
e) Legally, grades cannot be changed beyond the property line of the site.
f) Rate of stormwater runoff leaving the site after construction not to exceed the pre-construction rate.
g) Grading design should optimize cut and fill.
3.3.2.2.1 The submitted grading plan should include the following:
a) All existing and proposed features of the site, including all building with plinth level;
b) Structures such as walls, walks, steps, roads;
c) Utilities such as water lines, sewer and stormwater drainage, electrical lines; and
d) Utility structures like manholes, junction boxes, sewage treatment plant, septic tank, soak pit, water tanks, water treatment plant, transformers and all underground structures indicated appropriately.
Proposed features shall be indicated in firm lines and existing features in dash.
a) General landform concept graphically represented with appropriate symbols and abbreviations (see 3.3.2.4).
b) Proposed contour lines should be integrated with existing and proposed elevations within the project site.
c) Location of swales and surface water flow, surface and subsurface soil drainage system or water harvesting systems.
d) Location of drainage catchments, areas of retention/detention or disposal/outfall point as the case may be.
e) Spot grades on road, walks, and swales including top level and relevant invert levels of all utilities and utilities structures as mentioned above; critical spot elevation to be established (see 3.3.2.3).
The planting plan shall be drawn to a scale of not less than 1 in 200 for a site up to one hectare and not less than 1 in 500 for a site up to 10 hectare and not less than 1 in 1 000 for site more than 10 hectare with part plans at 1 in 200 of two of the design areas. Planting plan should include plant material schedule as shown in Table 1. The planting plan and landscape plan shall show identical information to avoid conflict between both plans. The planting plan shall include the layouts as per the following requirements, drawn to the scale:
a) Location of proposed trees, shrubs, ground covers including grass area indicated clearly with appropriate symbols and legend shall be indicated.
b) The shape, size, diameter of canopy of plants with their possible growth in coming 3 years shall be indicated.
c) Functional attributes and growth pattern tabulation shall be attached as given in Table 2, as an annex.
d) All existing vegetation shall be marked on the landscape plan and areas designated for preservation of existing vegetation on site shall be demarcated clearly (see also 11.1.2).
e) A concept plan of scale not less than 1 in 1 000 indicating the intent of the design with respect to the functions for various parts of the scheme shall be included with a short narrative, where applicable.
| Sl No. | Tree No. | Code | Botanical Name | Common Name | Quantity |
|---|---|---|---|---|---|
| (1) | (2) | (3) | (4) | (5) | (6) |
| Sl No. | Relevant Features | DescriptionPlant-1 |
|---|---|---|
| (1) | (2) | (3) |
| i) | Botanical name | |
| ii) | Common name | |
| iii) | Plant code | |
| iv) | Type (Evergreen/Deciduous) | |
| v) | Height | |
| vi) | Spread/Canopy | |
| vii) | Form of tree | |
| viii) | Flower colour | |
| ix) | Seasonal duration |
The materials and finishing plan shall be drawn to a scale of not less than 1 in 500 for a site up to 10 hectare and not less than 1 in 1 000 for site more than 10 hectare. The plan shall include materials specifications such as type, colour, size, thickness, and surface treatment.
Construction details, specifications and methods used for the following landscape elements are to be included, where applicable:
a) All paved areas for pedestrian and vehicular use, including edges, kerbs, bumper stops, steps, ramps, planters, railings or other protective devices; tree protection with tree grating, tree guard, etc; provision for wheel chair access and movement, and other accessibility details in accordance with 13 of Part 3 ‘Development Control Rules and General Building Requirements’ of the Code.
b) Boundary wall, fence, retaining wall, etc.
c) Structures in landscape such as gatehouses, kiosks, toilets, pergolas, space frame, pools, ponds, water bodies, any other special features.
d) Site utilities such as stormwater drains, manholes, catch basins, outdoor lighting fixtures, electric feeder pillars, junction box, fire hydrant, garbage collection points, litter bins.
e) Outdoor signage and street furniture.
f) Play equipment and tot lots, where appropriate.
g) Any other relevant detail or information.
The irrigation plan shall be drawn to a scale of not less than 1 in 500 for a site up to one hectare and not less than 1 in 1 000 for site more than one hectare. The plan shall include the following information:
a) Source of irrigation water.
b) Type of water conserving irrigation systems proposed, if any.
c) Extent of supplementary irrigation provided by water harvesting measures, if any.
d) Layout of the irrigation system proposed (including arrangement of hydrants or sprinklers indicating location and type with typical details and specifications, etc as applicable to the irrigation system).
f) Spot elevation of building floor finish level, steps, walls, terraces and other such structures.
g) Changes in direction or rate of slope.
Spot elevations shall be used to supplement contours in the following situations:
a) To indicate variations from the normal slope or gradient between contour lines.
b) To indicate elevations of intersecting planes and lines, like corners of buildings, walls, steps and kerbs.
c) To indicate elevations at top and bottom of vertical elements like walls, steps and kerbs.
d) To indicate floor and entrance elevations.
e) To indicate elevations of high and low points.
f) To indicate top elevations of utilities and utilities structure.
Slopes are expressed as follows:
a) Percentage (of slope) = (Vertical rise × 100)/(Horizontal distance) ,
for example, (1×100)/(50)=2 percent
b) Proportion (of slope) = Vertical rise (1.0 m) Horizontal distance, for example 1 m in 50 m or 1 : 50
c) Degree of slope, expressed as angle, for example, 10°, 15°, etc.
3.3.2.4 Typical grading symbols and abbreviations
| Symbol | Description |
|---|---|
| - -(100)- - | Existing contour |
| - 100 - | Proposed contour |
| (100.5) | Existing spot elevation |
| 100.5 (Bold) | Proposed spot elevation |
| CB | Catch basin |
| FFL | Finished floor level |
| FGL | Finished ground level |
| TW/BW | Top of wall/Bottom of wall |
| TK/BK | Top of kerb/Bottom of kerb |
| HP/LP | High point/Low point |
| IL | Invert level |
| x) | Zone (Functional attributes) |
| xi) | Characteristics |
| xii) | Function |
| xiii) | Remarks (including with regard to poisonous character and health ground) |