BUREAU OF INDIAN STANDARDS
- FOREWORD
- 1 SCOPE
- 2 TERMINOLOGY AND CONVENTIONAL SYMBOLS
- 3 GENERAL REQUIREMENTS
- 4 PLANNING OF ELECTRICAL INSTALLATIONS
- 5 DISTRIBUTION OF SUPPLY AND CABLING
- 6 WIRING
- 7 FITTINGS AND ACCESSORIES
- 8 EARTHING
- 9 INSPECTION, TESTING AND VERIFICATION OF INSTALLATION
- 10 ALLIED/MISCELLANEOUS SERVICES
- 11 LIGHTNING PROTECTION OF BUILDINGS
- 12 ELECTRICAL INSTALLATIONS FOR CONSTRUCTION AND DEMOLITION
- SITES
- 13 PROTECTION OF HUMAN BEINGS FROM ELECTRICAL HAZARDS
- ANNEX A DRAWING SYMBOLS FOR ELECTRICAL INSTALLATIONS
- IN BUILDINGS
- ANNEX B EXTRACTS FROM CENTRAL ELECTRICITY AUTHORITY
- (MEASURES RELATING TO SAFETY AND ELECTRIC SUPPLY)
- REGULATION, 2010 FURTHER AMENDED IN 2015
- ANNEX C AREA REQUIRED FOR TRANSFORMER ROOM AND
- SUBSTATION FOR DIFFERENT CAPACITIES
- ANNEX D ADDITIONAL AREA REQUIRED FOR GENERATOR IN ELECTRIC
- SUBSTATION
- ANNEX E CHECKLIST FOR INSPECTION, HANDING OVER AND
- COMMISSIONING OF VARIOUS EQUIPMENT OF SUBSTATION
- ANNEX F CHECKLIST FOR INSPECTION, HANDING OVER AND
- COMMISSIONING OF EARTHING PITS
- ANNEX G FORM OF COMPLETION CERTIFICATE
- LIST OF STANDARDS
This Code (Part 8/Section 2) covers essential requirements for electrical and allied installations in buildings.
This Section was first published in 1970 and was subsequently revised in 1983 and 2005. In the first revision, general guidance for electrical wiring installation in industrial location where voltage supply normally exceeds 650 V was included. This Section was also updated based on the existing version of the Indian Standards. The importance of pre-planning and exchange of information among all concerned agencies from the earlier stages of building work was emphasized.
In the second revision of 2005, the title of this Section was modified from the erstwhile ‘Electrical Installations’ to ‘Electrical and Allied Installations’ to reflect the provisions included on certain allied installations. The significant changes incorporated in the last revision included, thorough change in the risk assessment procedure for lightning including some other changes in the provision of lightning protection of building; alignment of some of the provisions of wiring with the practices prevalent at that time; modification of definitions in line with terminologies used at national and international level and addition of some new definitions; incorporation of provisions on installation of distribution transformer inside the multi-storeyed building; introduction of concept of energy conservation in lighting and introduction of concept of various types of earthing in building installation.
All electrical installations in India come under the purview of The Indian Electricity Act, 2003 and the rules and regulations framed thereunder. In the context of the buildings, both buildings (the structure itself) and the building services (not just the electrical services, but all other services that use electricity or have an interface with the electrical system) are required to follow these. The erstwhile Indian Electricity Rules, 1956 were superseded by various Central Electricity Authority Regulations. While revising the provisions of this Section of the Code, care has been taken to align the same with the provisions of the relevant regulations, particularly, Central Electricity Authority (Measures Relating to Safety and Electric Supply) Regulations, 2010, amended in 2015. In this revision, in addition to above, the following major modifications have been incorporated:
a) Various new terms and their definitions have been added and existing terms and definitions have also been updated based on current developments at national and international level.
b) Provisions relating to location and other requirements relating to layout, environmental and safety aspects for different substation apparatus/equipment and generating sets have been reviewed and updated.
c) Provisions relating to location of compact substations have been added.
d) Requirements for electrical supply system for life and safety services have been included.
e) Provisions relating to reception and distribution of supply and wiring installations have been updated with due cognizance to Indian Standards formulated for various wiring systems.
f) Provisions relating to installation of energy meters have been updated.
g) Discrimination, cascading and limitation concepts for the coordination of protective devices in electrical circuits have been introduced.
h) Socket outlets with suitable circuit breakers, conforming to following Indian Standards have been recommended for industrial and commercial applications, either indoors or outdoors:
-
IS/IEC 60309-1:2002 ‘Plugs, socket-outlets and couplers for industrial purposes — Part 1: General requirements’; and
-
IS/IEC 60309-2:2002 ‘Plugs, socket-outlets and couplers for industrial purposes — Part 2: Dimensional Interchangeability Requirements for Pin and Contact-Tube Accessories’.
j) Provisions relating to earthing/grounding have been substantially revised and updated.
k) Provisions relating to lightning protection of buildings have been revamped based on the current national and international developments.
m) Provisions relating to renewable energy sources for building, such as solar PV system; aviation obstacle
lights; electrical supply for electric vehicle charging and car park management; etc, have been included.
n) New provisions relating to electrical installations for construction sites and demolition sites have been included.
p) New provisions relating to protection of human beings from electrical hazards and protection against fire in the building due to leakage current have been included.
q) Typical formats for checklists for handing over and commissioning of substation equipment and earthing pit have been included.
This Section has to be read together with Part 8 ‘Building Services, Section 1 Lighting and Natural Ventilation’ of the Code for making provision for the desired levels of illumination as well as ventilation for different locations in different occupancies; and also with Part 4 ‘Fire and Life Safety’ of the Code for list of emergency fire and life safety services and other sections of Part 8 ‘Building Services’ and Part 9 ‘Plumbing Services’ for electricity related requirements and integration thereof. Utmost importance should be given in the installation of electrical wiring to prevent short circuiting and the hazards associated therewith.
Notwithstanding the provisions given in this Section and the National Electrical Code, 2011 the provisions of the Indian Electricity Act, 2003 and the rules and regulations framed thereunder have to be necessarily complied with.
The information contained in this Section is largely based on the following Indian Standards/Special Publication:
IS 732 : 1989 Code of practice for electrical wiring installations (third revision) (under revision)
IS 3043 : 1987 Code of practice for earthing (first revision) (under revision)
IS 4648: 1968 Guide for electrical layout in residential buildings
IS 12032 (Part 11): 1987 Specification for graphical symbols for diagrams in the field of electro technology: Part 11 Architectural and topographical installation plan and diagrams
IS/IEC 62305-1 : 2010 Protection against lightning: Part 1 General principles
IS/IEC 62305-2 : 2010 Protection against lightning: Part 2 Risk management
IS/IEC 62305-3 : 2010 Protection against lightning: Part 3 Physical damage to structures and life hazard
IS/IEC 62305-4 : 2010 Protection against lightning: Part 4 Electrical and electronic systems within structures
SP 30 : 2011 National Electrical Code, 2011 (first revision)
It may be noted that some of the above standards are currently under revision. The revised version when available should also be referred.
Considerable assistance has also been drawn from following International Standards while formulating this Section:
IEC 60364-4-41 : 2005 Low-voltage electrical installations — Part 4-41: Protection for safety — Protection against electric shock
IEC 60364-4-43 : 2008 Low-voltage electrical installations — Part 4-43: Protection for safety — Protection against overcurrent
IEC 60364-4-44 : 2007 Low-voltage electrical installations — Part 4-44: Protection for safety — Protection against voltage disturbances and electromagnetic disturbances
IEC 60364-5-51 : 2005 Electrical installations of buildings — Part 5-51: Selection and erection of electrical equipment — Common rules
IEC 60364-5-54 : 2011 Low-voltage electrical installations — Part 5-54: Selection and erection of electrical equipment — Earthing arrangements and protective conductors
IEC 60364-7 series Low-voltage electrical installations — Part 7: Requirements for special installations or locations
IEC 61439-1 : 2011 Low-voltage switchgear and controlgear assemblies and bus trunking — Part 1: General rules
IEC 61439-2 : 2011 Low-voltage switchgear and controlgear assemblies and bus trunking — Part 2: Power switchgear and controlgear assemblies
IEC 61439-6 : 2012 Low-voltage switchgear and controlgear assemblies and bus trunking — Part 6: Busbar trunking systems (busways)
All standards, whether given herein above or cross-referred to in the main text of this Section, are subject to revision. The parties to agreement based on this Section are encouraged to investigate the possibility of applying the most recent editions of the standards.
For the purpose of deciding whether a particular requirement of this Section is complied with, the final value, observed or calculated, expressing the result of a test or analysis, shall be rounded off in accordance with IS 2 : 1960 ‘Rules for rounding off numerical values (revised)’. The number of significant places retained in the rounded off value should be the same as that of the specified value in this Section of the Code.