BUREAU OF INDIAN STANDARDS
- 1 SCOPE ... 5
- 2 TERMINOLOGY ... 5
- 3 PRESSURE REGULATIONS ... 5
- 4 SERVICE SHUT-OFF VALVES ... 6
- 5 EXISTING WORK ... 6
- 6 RULES FOR TURNING GAS ON ... 6
- 7 RULES FOR SHUTTING OFF THE GAS ... 6
- 8 INSTALLATION OF GAS PIPES ... 7
- 9 INSPECTION OF SERVICES ... 8
- 10 LEAKAGE CHECK ... 9
- 11 USE OF LIQUEFIED PETROLEUM GAS (LPG) ... 9
- 12 USE OF PIPED NATURAL GAS (PNG) ... 14
- 13 USE OF MEDICAL GAS PIPELINE SYSTEM (MGPS) ... 16
- LIST OF STANDARDS ... 17
This Code (Part 9/Section 4) covers the safe use of gases for purposes like fuel, lighting and medical in buildings.
The use of gases for fuel and lighting purposes in buildings is becoming more and more common in different parts of the country, and with the advent of new petroleum complexes and piped gas system, community gas supply is bound to become one of the important services like electricity and water supply in buildings.
The use of liquefied petroleum gas supplied in containers and cylinders is already quite popular. On release of pressure, by opening the valve, they readily convert into the gaseous phase. In this state they present a hazard comparable to any inflammable natural or manufactured gas, except that being heavier than air, low level ventilation is necessary to avoid inflammable concentration of gas. Similarly, a series of precautions and regulations are necessary for laying of natural gas pipelines from city gas distribution entity to building premises and finally in the use location. Of late, the use of medical gases in hospitals through pipelines has become quite prevalent due to associated advantages; however, this needs to be supplemented with required care and precautions.
A minimum set of safety provisions are, therefore, laid down to safeguard the gas piping installation and the mode of operation in the interest of public safety.
In the first version of the Code formulated in 1970, three separate Sections of Part 9 Plumbing services, were brought out, namely, Section 1 Water supply, Section 2 Drainage and sanitation, and Section 3 Gas supply. These Sections were subsequently revised in 1983.
In the first revision, in 1983, the safe distance between gas piping and electrical wiring system was modified as well as between gas piping and steam piping was incorporated. Additional information regarding the handling, use, storage and transportation of LPG in cylinders exceeding 500 ml water capacity were included. Provisions relating to LPG cylinders, installations regarding some aspects, such as jointing compound used at joints, painting of gas piping, details of fire extinguishers, total quantity of LPG at stationary and portable installations in proportion to the floor area were added. Also, some provisions of LPG bulk storage installations were introduced.
In the second revision in 2005, the Part 9 was renamed as ‘Plumbing Services (Including Solid Waste Management)’ and provisions on solid waste management were included for the first time under Section 1 which contained in it, Water Supply, Drainage and Sanitation. Gas Supply was covered in Section 2 of Part 9 of the Code. In this second revision, provisions with regard to pressure regulations were modified; in the provision of service shut-off valves, number of additional shut-off valves were specified; in the provision of installation of gas pipe, new materials for pipes were mentioned; the minimum diameter for gas pipe was reduced to 8 mm; the colour for pipe line for supplying natural gas was specified; the provisions regarding protection against the corrosion were modified; the process of installation of meters were clarified; and additional method for detection of leakage of gas was recommended.
In this third revision of the Code, to comprehensively address the various and distinct features related to the plumbing aspects, this Part 9 has been rearranged as follows:
Section 1 Water supply
Section 2 Drainage and sanitation
Section 3 Solid waste management
Section 4 Gas supply
Based on the experience gained in the use of this Section, the provisions have been modified in this revision. The significant changes incorporated in this revision include the following:
a) Certain terminologies have been included and others have been updated.
b) Provision of use of fire stops/sleeves at openings has been included.
c) Clause on use of use of liquefied petroleum gas has been completely revised.
d) A new detailed clause on use of piped natural gas has been included.
e) A new clause on medical gas pipeline system has been included.
f) Cross-referred standards have been updated.
It may also be noted that the following Indian Standards have also been formulated on design and installation of natural gas pipelines:
IS 15663 Code of practice for design and installation of natural gas pipelines:
(Part 1): 2006 Laying of pipelines
(Part 2): 2006 Laying of pipelines in crossings
(Part 3): 2006 Pre-commissioning and commissioning of pipelines
While implementing this standard, compliance with statutory regulations shall be ensured.
The information regarding the use of liquefied petroleum gas has been largely based on the following Indian Standards:
IS 6044 Liquefied petroleum gas storage installations — Code of practice:
(Part 1): 2013 Residential, commercial and industrial cylinder installations (second revision)
(Part 2): 2001 Commercial, industrial and domestic bulk storage installations (first revision)
All standards, whether given herein above or cross-referred to in the main text of this Section, are subject to revision. The parties to agreement based on this Section are encouraged to investigate the possibility of applying the most recent editions of the standards.