Elevated helipad structures shall be designed as per the latest guidelines of Directorate General of Civil Aviation and International Civil Aviation Organization's Heliport Manual.
3.7.1 Structural Design
Elevated helipads may be designed for a specific helicopter type though greater operational flexibility will be obtained from a classification system of design. The final approach and take-off area (FATO) should be designed for the largest or heaviest type of helicopter that is anticipated to use the helipad, and account taken of other types of loading such as personnel, freight, snow, refueling equipment, etc. For the purpose of design, it is to be assumed that the helicopter will land on two main wheels, irrespective of the actual number of wheels in the undercarriage, or on two skids, if they are fitted. The loads imposed on the structure should be taken as point loads at the wheel centres as shown below:
| Helicopter Category | Maximum Take-off Mass | Point Load for Each Wheel | Under-Carriage Wheel Centres | Super-imposed Load SHa | Super-imposed Load SHb | |
| kg(2) | kN(3) | kN(4) | m(5) | kN/m² (6) | kN/m² (7) | |
| 1 | Up to 2 300 | Up to 22.6 | 12.0 | 1.75 | 0.5 | 1.5 |
| 2 | 2 301-5 000 | 22.6-49.2 | 25.0 | 2.0 | 0.5 | 2.0 |
| 3 | 5 001-9 000 | 49.2-88.5 | 45.0 | 2.5 | 0.5 | 2.5 |
| 4 | 9 001-13 500 | 88.5-133.0 | 67.0 | 3.0 | 0.5 | 3.0 |
| 5 | 13 501-19 500 | 133.0-192.0 | 96.0 | 3.5 | 0.5 | 3.0 |
| 6 | 19 501-27 000 | 192.0-266.0 | 133.0 | 4.5 | 0.5 | 3.0 |
3.7.2 The FATO should be designed for the worse condition derived from consideration of the following two cases.
3.7.3 Case A — Helicopter on Landing
When designing a FATO on an elevated helipad, and in order to cover the bending and shear stresses that result from a helicopter touching down, the following
should be taken into account:
a) Dynamic load due to impact on touchdown — This should cover the normal touchdown, with a rate of descent of 1.8 m/s, which equates to the serviceability limit state. The impact load is then equal to 1.55 times the maximum take-off mass of the helicopter. The emergency touchdown should also be covered at a rate of descent of 3.6 m/s (12 ft/s), which equates to the ultimate limit state. The partial safety factor in this case should be taken as 1.66. Therefore,
The sympathetic response factor discussed at 3.7.3 (b) below should be applied.
b) Sympathetic response on the FATO — The dynamic load should be increased by a structural response factor dependent upon the natural frequency of the platform slab when considering the design of supporting beams and columns. This increase in loading will usually apply only to slabs with one or more freely supported edges. It is recommended that the average structural response factor (R) of 1.3 should be used in determining the ultimate design load.
c) Over-all superimposed load on the FATO ( SHa ) — To allow for snow load, personnel, freight and equipment loads, etc, in addition to wheel loads, an allowance of 0.5 kN/m ² should be included in the design.
d) Lateral load on the platform supports — The supports of the platform should be designed
to resist a horizontal point load equivalent to 0.5 maximum take-off mass of the helicopter, together with the wind loading [see (f)], applied in the direction which will provide the greater bending moments.
e) Dead load of structural members — The partial safety factor to be used for the dead load should be taken as 1.4.
f) Wind loading — Shall be as per 4.
g) Punching shear — Check for the punching shear of an undercarriage wheel or skid using the ultimate design load with a contact area of 64.5 × 10³ mm ² .
3.7.4 Case B — Helicopter at Rest
When designing a FATO on an elevated helipad, and in order to cover the bending and shear stresses from a helicopter at rest, the following should be taken into account:
a) Dead load of the helicopter — Each structural element shall be designed to carry the point load, in accordance with the table under 3.7.1, from the two main wheels or skids applied simultaneously in any position on the FATO so as to produce the worst effect from both bending and shear.
b) Over-all superimposed load ( SHb ) — In addition to wheel loads, an allowance for overall superimposed load given in the table under 3.7.1, over the area of the FATO, should be included in the design.
c) Dead load on structural members and wind loading — The same factors should be included in the design for these items as given for Case A.
NOTE — The above design loads for helicopters at rest are summarized below:
Design Load for Helicopter on Landing — Case A
| i) Superimposed loads: | ||
| a) Helicopter | 2.5 LH distributed as two point loads at the wheel centres for the helicopter category given in the informal table under3.7.1Average value for R = 1.3. | |
| b) Lateral load | 1.6 L H2 applied horizontally in any direction | |
| c) Over-all superimposed load | Load at platform level together with the maximum wind loading. 1.4 SHa over the whole area of the platform ( SHa given in the informal table under3.7.1) | |
| ii) Dead load | 1.4G | |
| iii) Wind loading | 1.4W | |
| iv) Punching shear check | 2.5 LHR load over tyre skid contact area of 64.5 × 10³ mm² | |
Design Load for Helicopter at Rest — Case B
| i) Superimposed loads: | |
| a) Helicopter | 1.6 LH distributed as two point loads at the wheel centres for the helicopter cat given in the informal table under 3.7.1 |
| b) Over-all superimposed load (Personnel, freight, etc) | 1.6 SHb over the whole area of the platform. SHb given in the informal table under 3.7.1 |
| ii) Shear check | Check as appropriate |
| Symbol | Meaning |
| L | |