8.1 Every test of material as required in this Part or by the Authority shall be carried out in accordance with the methods of test prescribed in relevant Indian Standards. In cases of methods of tests for which Indian Standards are not available, the same shall conform to the methods of tests issued by the Authority or their agent. A list of Indian Standard methods of test is given at the end of this Part of the Code as the ‘accepted standards’. Laboratory tests shall be conducted by recognized laboratories acceptable to the Authority.
8.1.1 The manufacturer/supplier shall satisfy himself that materials conform to the requirements of the specifications and if requested shall supply a certificate to this effect to the purchaser or his representative. When such test certificates are not available, the specimen of the material shall be tested.
Following are the Indian Standards for various building materials and components, to be complied with in fulfillment of the requirements of the Code.
In the following list, while enlisting the Indian Standards, the materials have been categorized in such a way as to make the list user friendly. In the process, if so required, some of the standards have been included even in more than one category of products, such as in the category based on composition as well as on end application of the materials. The list has been arranged in alphabetical order of their principal category as given below:
-
Aluminium and other light metals and their alloys
-
Bitumen and tar products
-
Bricks, blocks and other masonry building units
-
Builder's hardware
-
Building chemicals
-
Building lime and products
-
Clay and stabilized soil products
-
Cement and concrete (including steel reinforcement for concrete)
-
Composite matrix products (including cement and resin matrix products)
-
Conductors and cables
-
Doors, windows and ventilators
-
Electrical wiring, fittings and accessories
-
Fillers, stoppers and putties
-
Floor covering, roofing and other finishes
-
Glass
-
Gypsum based materials
| 17) Mortar (including sand for mortar) | IS No. | Title | |
| 18) Paints and allied products | 1284 : 1975 | Wrought aluminium alloys bolt and screw stock for general engineering purposes (second revision) | |
| 19) Polymers, plastics and geosynthetics/geotextiles | |||
| 20) Sanitary appliances and water fittings | 1285 : 2002 | Specification for wrought aluminium and aluminium alloys — Extruded round tube and hollow sections for general engineering purposes (third revision) | |
| 21) Steel and its alloys | |||
| 22) Stones | |||
| 23) Structural sections | |||
| 24) Thermal insulation materials | 2479 : 1981 | Colour code for the identification of aluminium and aluminium alloys for general engineering purposes (second revision) | |
| 25) Threaded fasteners, rivets and nails | |||
| 26) Timber, bamboo and other lignocellulosic building materials | |||
| 27) Unit weights of building materials | 2676 : 1981 | Dimensions for wrought aluminium and aluminium alloy sheet and strip | |
| 28) Waterproofing and damp-proofing materials | |||
| 29) Welding electrodes and wires | 2677 : 1979 | Dimensions for wrought aluminium and aluminium alloys, plates and hot rolled sheets | |
| 30) Wire ropes and wire products (including wire for fencing) | |||
| 3577 : 1992 | Wrought aluminium and its alloys — Rivet, bolt and screw stock — Dimensions and tolerances (first revision) | ||
| 1. ALUMINIUM AND OTHER LIGHT METALS AND THEIR ALLOYS | |||
| IS No. | Title | 3965 : 1981 | Dimensions for wrought aluminium and aluminium alloys bar, rod and section (first revision) |
| 733 : 1983 | Specification for wrought aluminium and aluminium alloys bars, rods and sections for general engineering purposes (third revision) | 6477 : 1983 | Dimensions for wrought aluminium and aluminium alloys extruded hollow sections |
| 734 : 1975 | Wrought aluminium and aluminium alloys forging stock and forgings (for general engineering purposes) (second revision) | 14712 : 1999 | Specification for wrought aluminium and its alloys — Chequered/tread sheets for general engineering purposes |
| 736 : 1986 | Specification for wrought aluminium and aluminium alloys plate for general engineering purposes (third revision) | ||
| IS No. | Title | IS No. | Title |
| 702 : 1988 | Specification for industrial bitumen (second revision) | 9381 : 1979 | Methods for testing tar and bituminous materials: Determination of FRAASS breaking point of bitumen |
| 1201 to 1220 | Methods for testing tar and bituminous materials (first revision) | Methods for testing tar and bituminous materials: Determination of FRAASS breaking point of bitumen | |
| 1201 : 1978 | Sampling (first revision) | 9382 : 1979 | Methods for testing tar and bituminous materials: Determination of effect of heat and air by thin film oven test |
| 1202 : 1978 | Determination of specific gravity (first revision) | Methods for testing tar and bituminous materials: Determination of effect of heat and air by thin film oven test | |
| 1203 : 1978 | Determination of penetration (first revision) | 10511 : 1983 | Method for determination of asphaltenes in bitumen by precipitation with normal haptane |
| 1204 : 1978 | Determination of residue of specified penetration (first revision) | Method for determination of asphaltenes in bitumen by precipitation with normal haptane | |
| 1205 : 1978 | Determination of softening point (first revision) | 10512 : 2003 | Method for determination of wax content in bitumen (first revision) |
| 1206 | Determination of viscosity | 13758 | Coal tar pitch — Methods of test |
| (Part 1) : 1978 | Industrial viscosity (first revision) | (Part 1) : 1993 | Determination of matter insoluble in quinoline |
| (Part 2) : 1978 | Absolute viscosity (first revision) | Determination of matter insoluble in quinoline | |
| (Part 3) : 1978 | Kinematic viscosity (first revision) | (Part 2) : 1993 | Determination of coking value |
| 1207 : 1978 | Determination of equiviscous temperature (EVT) (first revision) | 15172 : 2002 | Methods for testing tar and bituminous materials — Determination of curing index for cutback bitumens |
| 1208 : 1978 | Determination of ductility (first revision) | Methods for testing tar and bituminous materials — Determination of curing index for cutback bitumens | |
| 1209 : 1978 | Determination of flash point and fire point (first revision) | 15173 : 2002 | Methods for testing tar and bituminous materials — Determination of breaking point for cationic bitumen emulsion |
| IS No. | Title | IS No. | Title |
| sliding door bolts for use with padlocks (third revision) | 9899 : 1981 | Specification for hat coat and wardrobe hooks | |
| 3564 : 1995 | Specification for door closers (hydraulically regulated) (second revision) | 10019 : 1981 | Specification for mild steel stays and fasteners |
| 10090 : 1982 | Specification for numericals | ||
| 3818 : 1992 | Specification for continuous (piano) hinges (third revision) | 10342 : 1982 | Specification for curtain rail system |
| 12817 : 2013 | Specification for stainless steel butt hinges (second revision) | ||
| 3828 : 1966 | Specification for ventilator chains | ||
| 3843 : 1995 | Specification for steel backflap hinges (first revision) | 12867 : 1989 | Specification for PVC hand rails covers |
| 3847 : 1992 | Specification for mortice night latches (second revision) | 14912 : 2001 | Specification for door closers concealed type (hydraulically regulated) |
| 4621 : 1975 | Specification for indicating bolts for use in public baths and lavatories (first revision) | 15833 : 2009 | Specification for stainless steel tower bolts |
| 4948 : 2002 | Specification for welded steel wire fabric for general use (second revision) | 15834 : 2008 | Specification for stainless steel sliding door bolts for use with padlocks |
| 4992 : 1975 | Specification for door handles for mortice locks (vertical type) (first revision) | 16015 : 2013 | Specification for mortice locks with lever mechanism (vertical type, sliding door locks and dead locks) |
| 5187 : 1972 | Specification for flush bolts (first revision) | 16016 : 2013 | Specification for cylindrical locks with pin tumbler mechanism |
| 5899 : 1970 | Specification for bathroom latches | 5. BUILDING CHEMICALS | |
| 5930 : 1970 | Specification for mortice latch (vertical type) | a) Anti-termite Chemicals | |
| 6315 : 1992 | Specification for floor springs (hydraulically regulated) for heavy doors (second revision) | IS No. | Title |
| 8944 : 2005 | Specification for chlorpyrifos emulsifiable concentrates (first revision) | ||
IS No. Title
1838 Specification for preformed fillers for expansion joint in concrete pavements and structures (non-extruding and resilient type)
(Part 1): 1983 Bitumen impregnated fibre (first revision)
(Part 2): 1984 CNSL aldehyde resin and coconut pith
(Part 3): 2011 Polymer based
10566 : 1983 Methods of tests for preformed fillers for expansion joint in concrete paving and structural construction 11433 Specification for one grade polysulphide based joint sealant
(Part 1): 1985 General requirements
(Part 2): 1986 Methods of test 12118 Specification for two parts polysulphide based sealants
(Part 1): 1987 General requirements
(Part 2): 1987 Methods of test