Section 5 of Part 6 of the Code covers plain and reinforced concrete as also the prestressed concrete. The Section has been subdivided into the following sub-sections:
A Plain and Reinforced Concrete
5 B Prestressed Concrete
This sub-section 5A covers the structural design aspects of plain and reinforced concrete.
This sub-section 5A was first published in 1970 and was subsequently revised in 1983, to bring it in line with revised version of IS 456 : 1978 on which this chapter was based. Now this revision is intended to bring this subsection in line with the revised version of IS 456 : 2000.
This revision incorporates a number of important changes. The major thrust in the revision is on the following lines:
a) In recent years, durability of concrete structures have become the cause of concern to all concrete technologists. This has led to codify the durability requirements world over. In this revision of the Code, in order to introduce in-built protection from factors affecting a structure, earlier clause on durability has been elaborated and a detailed clause covering different aspects of design of durable structure has been incorporated.
b) Sampling and acceptance criteria for concrete have been revised. With this revision acceptance criteria has been simplified in line with the provisions given in BS 5328 (Part 4) : 1990 ‘Concrete: Part 4 Specification for the procedures to be used in sampling, testing and assessing compliance of concrete’.
Some of the significant changes incorporated in Section 5A (b) are as follows:
a) All the three grades of ordinary Portland cement, namely 33 grade, 43 grade and 53 grade and sulphate resisting Portland cement have been included in the list of types of cement used (in addition to other types of cement).
b) The permissible limits for solids in water have been modified keeping in view the durability requirements.
c) The clause on admixtures has been modified in view of the availability of new types of admixtures including superplasticizers.
d) In Table 2 ‘Grades of Concrete’, grades higher than M 40 have been included.
e) It has been recommended that minimum grade of concrete shall be not less than M 20 in reinforced concrete work (see also 5.1.3).
f) The formula for estimation of modulus of elasticity of concrete has been revised.
g) In the absence of proper correlation between compacting factor, vee-bee time and slump, workability has now been specified only in terms of slump in line with the provisions in BS 5328 (Parts 1 to 4).
h) Durability clause has been enlarged to include detailed guidance concerning the factors affecting durability. The table on ‘Environmental Exposure Conditions’ has been modified to include ‘very severe and ‘extreme’ exposure conditions. This clause also covers requirements for shape and size of member, depth of concrete cover, concrete quality, requirement against exposure to aggressive chemical and sulphate attack, minimum cement requirement and maximum water cement ratio, limits of chloride content, alkali silica reaction, and importance of compaction, finishing and curing.
j) A clause on ‘Quality Assurance Measures’ has been incorporated to give due emphasis to good practices of concreting.
k) Proper limits have been introduced on the accuracy of measuring equipments to ensure accurate batching of concrete.
m) The clause on ‘Construction Joints’ has been modified.
n) The clause on ‘Inspection’ has been modified to give more emphasis on quality assurance.
The significant changes incorporated in Section 5A (c) are as follows:
a) Requirements for ‘Fire Resistance’ have been further detailed.
b) The figure for estimation of modification factor for tension reinforcement used in calculation of basic values of span to effective depth to control the deflection of flexural member has been modified.
c) Recommendations regarding effective length of cantilever have been added.
d) Recommendations regarding deflection due to lateral loads have been added.
e) Recommendations for adjustments of support moments in restrained slabs have been included.
f) In the determination of effective length of compression members, stability index has been introduced to determine sway or no sway conditions.
g) Recommendations have been made for lap length of hooks for bars in direct tension and flexural tension.
h) Recommendations regarding strength of welds have been modified.
Recommendations regarding cover to reinforcement have been modified. Cover has been specified based on durability requirements for different exposure conditions. The term ‘nominal cover’ has been introduced. The cover has now been specified based on durability requirement as well as for fire requirements.
The significant change incorporated in Section 5A (d) is the modification of the clause on Walls. The modified clause includes design of walls against horizontal shear.
In Section 5 on limit state method a new clause has been added for calculation of enhanced shear strength of sections close to supports. Some modifications have also been made in the clause on Torsion. Formula for calculation of crack width has been added (separately given in Annex F).
Working stress method has now been given in Annex B so as to give greater emphasis to limit state design. In this Annex, modifications regarding torsion and enhanced shear strength on the same lines as in Section 5 have been made.
Whilst the common methods of design and construction have been covered in this Code, special systems of design and construction of any plain or reinforced concrete structure not covered by this Code may be permitted on production of satisfactory evidence regarding their adequacy and safety by analysis or test or both (see 18).
In this Code it has been assumed that the design of plain and reinforced cement concrete work is entrusted to a qualified engineer and that the execution of cement concrete work is carried out under the direction of a qualified and experience supervisor.
This Section also introduces self-compacting concrete (see Annex A).
In the formulation of this subsection, assistance has been derived from the following publications:
BS 5328 (Part 1) : 1991 Concrete: Part 1 Guide to specifying concrete, British Standards Institution
BS 5328 (Part 2) : 1991 Concrete: Part 2 Methods for specifying concrete mixes, British Standards Institution
BS 5328 (Part 3) : 1990 Concrete: Part 3 Specification for the procedures to be used in producing and transporting concrete, British Standards Institution
BS 5328 (Part 4) : 1990 Concrete: Part 4 Specification for the procedures to be used in sampling, testing and assessing compliance of concrete, British Standards Institution
BS 8110 (Part 1) : 1985 Structural use of concrete: Part 1 Code of practice for design and construction, British Standards Institution
BS 8110 (Part 2) : 1985 Structural use of concrete: Part 2 Code of practice for special circumstances, British Standards Institution
ACI 318 : 1995 Building code requirements for reinforced concrete, American Concrete Institute
AS 3600 : 1988 Concrete structures, Standards Association of Australia
DIN 1045 July 1988 Structural use of concrete, design and construction, Deutsches Institut für Normung E.V.
CEB-FIP Model Code 1990, Comite Euro International Du Belon
All standards, whether given herein above or cross-referred to in the main text of this Section, are subject to revision. The parties to agreement based on this Section are encouraged to investigate the possibility of applying the most recent editions of the standards.
(a) General