2.0 For the purpose of this Section, the following definitions shall apply.
2.1 Anatomical Purpose Definitions
2.1.1 Bamboo — Tall perennial grasses found in tropical and sub-tropical regions. They belong to the family Poaceae and sub-family Bambusoidae.
2.1.2 Bamboo Culm — A single shoot of bamboo usually hollow except at nodes which are often swollen.
2.1.3 Bamboo Clump — A cluster of bamboo culms emanating from two or more rhizomer in the same place.
2.1.4 Cellulose — A carbohydrate, forming the fundamental material of all plants and a main source of the mechanical properties of biological materials.
2.1.5 Cell — A fundamental structural unit of plant and animal life, consisting of cytoplasma and usually enclosing a central nucleus and being surrounded by a membrane (animal) or a rigid cell wall (plant).
2.1.6 Cross Wall — A wall at the node closing the whole inside circumference and completely separating the hollow cavity below from that above.
2.1.7 Hemi Cellulose — The polysaccharides consisting of only 150 to 200 sugar molecules, also much less than the 10 000 of cellulose.
2.1.8 Lignin — A polymer of phenyl propane units, in its simple form (C₆H₅CH₃CH₂CH₃)
2.1.9 Sliver — Thin strips of bamboo processed from bamboo culm.
2.1.10 Tissue — Group of cells, which in higher plants consist of (a) Parenchyma — a soft cell of higher plants
as found in stem pith or fruit pulp, (b) Epidermis — the outermost layer of cells covering the surface of a plant, when there are several layers of tissue.
2.2 Structural Purpose Definitions
2.2.1 Bamboo Mat Board — A board made of two or more bamboo mats bonded with an adhesive.
2.2.2 Beam — A structural member which supports load primarily by its internal resistance to bending.
2.2.3 Breaking Strength — A term loosely applied to a given structural member with respect to the ultimate load it can sustain under a given set of conditions.
2.2.4 Bundle-Column — A column consisting of three or more number of culm bound as integrated unit with wire or strap type of fastenings.
2.2.5 Centre Internode — A test specimen having its centre between two nodes.
2.2.6 Characteristic Load — The value of loads which has a 95 percent probability of not exceeding during the life of the structure.
2.2.7 Characteristic Strength — The strength of the material below which not more than 5 percent of the test results are expected to fall.
2.2.8 Cleavability — The ease with which bamboo can be split along the longitudinal axis. The action of splitting is known as cleavage.
2.2.9 Column — A structural member which supports axial load primarily by inducing compressive stress along the fibres.
2.2.10 Common Rafter — A roof member which supports roof battens and roof coverings, such as boarding and sheeting.
2.2.11 Curvature — The deviation from the straightness of the culm.
2.2.12 Delamination — Separation of mats through failure of glue.
2.2.13 End Distance — The distance measured parallel to the fibres of the bamboo from the centre of the fastener to the closest end of the member.
2.2.14 Flatten Bamboo — Bamboo consisting of culms that have been cut and unfolded till it is flat. The culm thus is finally spread open, the diaphragms (cross walls) at nodes removed and pressed flat.
2.2.15 Full Culm — The naturally available circular section/shape.
2.2.16 Fundamental or Ultimate Stress — The stress which is determined on a specified type/size of culms of bamboo, in accordance with standard practice and does not take into account the effects of naturally occurring characteristics and other factors.
2.2.17 Inner Diameter — Diameter of internal cavity of a hollow piece of bamboo.
2.2.18 Inside Location — Position in buildings in which bamboo remains continuously dry or protected from weather.
2.2.19 Joint — A connection between two or more bamboo structural elements.
2.2.20 Joist — A beam directly supporting floor, ceiling or roof of a structure.
2.2.21 Length of Internode — Distance between adjacent nodes.
2.2.22 Loaded End or Compression End Distance — The distance measured from the centre of the fastner to the end towards which the load induced by the fastener acts.
2.2.23 Matchet — A light cutting and slashing tool in the form of a large knife.
2.2.24 Mat — A woven sheet made using thin slivers.
2.2.25 Mortise and Tenon — A joint in which the reduced end (tenon) of one member fits into the corresponding slot (mortise) of the other.
2.2.26 Net Section — Section obtained by deducting from the gross cross-section (A), the projected areas of all materials removed by boring, grooving or other means.
2.2.27 Node — The place in a bamboo culm where branches sprout and a diaphragm is inside the culm and the walls on both sides of node are thicker.
2.2.28 Outer Diameter — Diameter of a cross-section of a piece of bamboo measured from two opposite points on the outer surface.
2.2.29 Outside Location — Position in building in which bamboos are occasionally subjected to wetting and drying as in case of open sheds and outdoor exposed structures.
2.2.30 Permissible Stress — Stress obtained after applying factor of safety to the ultimate or basic stress.
2.2.31 Principal Rafter — A roof member which supports purlins.
2.2.32 Purlins — A roof member directly supporting roof covering or common rafter and roof battens.
2.2.33 Roof Battens — A roof member directly supporting tiles, corrugated sheets, slates or other roofing materials.
2.2.34 Roof Skeleton — The skelton consisting of bamboo truss or rafter over which solid bamboo purlins are laid and lashed to the rafter or top chord of a truss by means of galvanized iron wire, cane, grass, bamboo leaves, etc.
2.2.35 Slenderness Ratio — The ratio of the length of member to the radius of gyration is known as slenderness ratio of member. (The length of the member is the equivalent length due to end conditions).
2.2.36 Splits — The pieces made from quarters by dividing the quarters radially and cutting longitudinally.
2.2.37 Taper — The ratio of difference between minimum and maximum outer diameter to length.
2.2.38 Unloaded End Distance — The end distance opposite to the loaded end.
2.2.39 Wall Thickness — Half the difference between outer diameter and inner diameter of the piece at any cross-section.
2.2.40 Wet Location — Position in buildings in which the bamboos are almost continuously damp, wet or in contact with earth or water, such as piles and bamboo foundations.
2.3 Definitions Relating to Defects
2.3.1 Bamboo Bore/GHOON Hole — The defect caused by bamboo GHOON beetle (Dinoderus spp. Bostrychdae), which attacks felled culms.
2.3.2 Crookedness — A localized deviation from the straightness in a piece of bamboo.
2.3.3 Discolouration — A change from the normal colour of the bamboo which does not impair the strength of bamboo or bamboo composite products.
2.4 Definitions Relating to Drying Degrades
2.4.1 Collapse — The defect occurring on account of excessive shrinkage, particularly in thick walled immature bamboo. When the bamboo wall shrinks, the outer layers containing a larger concentration of strong fibro-vascular bundles set the weaker interior portion embedded in parenchyma in tension, causing the latter to develop cracks. The interior crack develops into a wide split resulting in a depression on the outer surface. This defect also reduces the structural strength of round bamboo.
2.4.2 End Splitting — A split at the end of a bamboo. This is not so common a defect as drying occurs both
from outer andinterior wall surfaces of bamboo as well as the end at the open ends.
2.4.3 Surface Cracking — Fine surface cracks not detrimental to strength. However, the cracking which occurs at the nodes reduces the structural strength.
2.4.4Wrinkled and Deformed Surface —Deformation in cross-section, during drying, which occurs in immature round bamboos of most species; in thick walled pieces, besides this deformation the outer surface becomes uneven and wrinkled. Very often the interior wall develops a crack below these wrinkles, running parallel to the axis.