11.1 Structural Design and Safety
For any building under the jurisdiction of these regulations, the structural design shall be carried out by registered/ licensed engineer/ structural engineer as specified in Chapter-14 of these regulations.
The structural design of different building elements shall conform to the relevant Indian Standards provided in Part 6 ‘Structural Design’ of NBC 2016 comprising of the following sections:
a) Section 1- Loads, forces and effects
b) Section 2- Soils and foundations
c) Section 3- Timber and bamboo
d) Section 4- Masonry
e) Section 5- Concrete
f) Section 6- Steel
g) Section 7- Prefabrication systems, building and mixed/composite construction.
h) Section 8- Glass and glazing
Requirements specified in the following Indian Standards, Codes and guidelines and other documents needs to be observed for structural safety and natural hazard protection of buildings etc:
a) For General Structural Safety
-
IS: 456:2000 “Code of Practice for Plain and Reinforced Concrete.
-
IS: 800-2007 “Code of Practice for General Construction in Steel.
-
IS: 801-1975 “Code of Practice for Use of Cold Formal Light Gauge Steel Structural Members in General Building Construction.
-
IS 875 (Part 2):1987 Design loads (other than earthquake) for buildings and structures Part2 Imposed Loads.
-
(Reference to Table 4.1- “Occupant Load” may be considered for design load) 5) IS 875 (Part 3):1987 Design loads (other than earthquake) for buildings and structures Part 3 Wind Loads.
-
IS 875 (Part 4):1987 Design loads (other than earthquake) for buildings and structures Part 4 Snow Loads.
-
IS 875 (Part 5):1987 Design loads (other than earthquake) for buildings and structures Part 5 special loads and load combination.
-
IS: 883:1994 “Code of Practice for Design of Structural Timber in Building.
-
IS: 1904:1986 (R 2005) “Code of Practice for Structural Safety of Buildings: Foundation”
-
IS 1905:1987 “Code of Practice for Structural Safety of Buildings: Masonry Walls.
-
IS 2911(Part 1): Section 1: 2010 “Code of Practice for Design and Construction of Pile Foundation Section 1.
(b) For Cyclone/ Wind-storm Protection
-
IS 875 (3):1987 "Code of Practice for Design Loads (other than Earthquake) for Buildings and Structures, Part 3, Wind Loads"
-
Guidelines (Based on IS 875 (3)-1987) for improving the Cyclonic Resistance of Low-rise houses and other building.
(c) For Earthquake Protection
-
IS: 1893 (Part 1,2,3,4) "Criteria for Earthquake Resistant Design of Structures"
-
IS:13920-2016 "Ductile Detailing of Reinforced Concrete Structures subjected to Seismic Forces - Code of Practice"
-
IS:4326-2013 "Earthquake Resistant Design and Construction of Buildings - Code of Practice (Second Revision)"
-
IS:13828-1993 "Improving Earthquake Resistance of Low Strength Masonry Buildings - Guidelines"
-
IS:138271993 "Improving Earthquake Resistance of Earthen Buildings- Guidelines"
-
IS:13935-2009 "Seismic Evaluation, Repair and Seismic Strengthening of Buildings - Guidelines”
(d) For Protection of Landslide Hazard (for protection of earth at different levels)
-
IS 14458 (Part 1): 1998 Guidelines for retaining wall for hill area: Part 1 Selection of type of wall.
-
IS 14458 (Part 2): 1997 Guidelines for retaining wall for hill area: Part 2 Design of retaining/breast walls.
-
IS 14458 (Part 3): 1998 Guidelines for retaining wall for hill area: Part 3 Construction of dry stone walls.
-
IS 14496 (Part 2): 1998 Guidelines for preparation of landslide – Hazard zonation maps in mountainous terrains: Part 2 Macro-zonation.
Note:
Whenever an Indian Standard including those referred in the National Building Code, the latest revision of the same shall be followed except specific criteria, if any, mentioned above against the provisions of that code.