A single figure descriptor of the sound absorption property of a material. It is the arithmetic mean of the sound absorption co-efficients at 250, 500, 1 000 and 2 000 Hz rounded off to the nearest multiple of 0.05.
2.24 Normalized Impact Sound Pressure Level, L n — Impact sound pressure level normalized for a standard absorption area in the receiving room.
NOTE — Normalized impact sound pressure level is usually used to characterize the insulation of a floor in a laboratory against impact sound in a stated frequency band (see Annex B).
2.25 Octave Band — Band of frequencies in which the upper limit of the band is twice the frequency of the lower limit.
2.26 Percentile Level, L A N , T - A -weighted sound pressure level obtained using time-weighting ° F which is exceeded for N percent of a specified time interval.
Example:
L A 9 0 , 1 h is the A-weighted level exceeded for 90 percent of 1 h. Percentile levels determined over a certain time interval cannot accurately be extrapolated to other time intervals. Timeweighting F ~ o r ~ S can be selected on most modern measuring instruments and used to determine the speed at which the instrument responds to changes in the amplitude of the signal. Time-weighting ° F ′ is faster than ° S ′ and so its use can lead to higher values when rapidly changing signals are measured.
2.27 Pink Noise — Sound with an uninterrupted frequency spectrum and a power which is steady within frequency band and proportional to centre frequency. An example is constant power level per octave band.
2.28 Pure Tone — A sound emitted at a single frequency.
2.29 Rating Level, L A r , T r — Equivalent continuous A-weighted sound pressure level of the noise, plus any adjustment for the characteristic features of the noise.
NOTE — This definition is used for rating industrial noise, where the noise is the specific noise from the source under investigation.
2.30 Reverberation Time, T — Time that would be required for the sound pressure level to decrease by 60 dB after the sound source has stopped.
NOTE — Reverberation time is usually measured in octave or third octave bands. It is not necessary to measure the decay over the full 60 dB range. The decay measured over the range 5 dB to 35 dB below the initial level is denoted by T 3 0 ° and over the range 5 dB to 25 dB below the initial level by T 2 0 °
2.31 Sound — A vibrational disturbance, exciting hearing mechanisms, transmitted in a predictable manner determined by the medium through which it propagates. To be audible the disturbance shall have to fall within the frequency range of 20 Hz to 20 000 Hz.
2.32 Sound Exposure Level, L A E - Level of a sound, of 1 s duration, that has the same sound energy as the actual noise event considered.
NOTES
1 The L A E of a discrete noise event is given by the formula:
where
P (t) = is the instantaneous A-weighted sound pressure in pascals (Pa);
t 2 – t 1 = is a stated time interval in seconds (s) long enough to encompass all significant sound energy of the event;
p o = is the reference sound pressure level (20μ Pa); and
t o = is the reference time interval (1 s).
2 L A E is also known as L A X (single-event noise exposure level).
2.33 Sound Power — The acoustic power of a sound source, expressed in Watts.
2.34 Sound Power Level, L w — The acoustic power radiated from a given sound source as related to a reference power level (typically 1 0 - 1 2 watts) and expressed in decibels as:
where
W = Acoustic power in watts.
By definition, 1 W therefore corresponds to 120 dB for L w
2.35 Sound Pressure, p — Root-mean-square value of the variation in air pressure measured in pascals (Pa), above and below atmospheric pressure, caused by the sound.
2.36 Sound Pressure Level, L p - Quantity of sound pressure, in decibels (dB), given by the formula:
where
p = is the root mean square sound pressure in pascals (Pa); and
p o = is the reference sound pressure (20μ Pa).
NOTE — The range of sound pressures for ordinary sounds is very wide. The use of decibels gives a smaller, more convenient range of numbers. For example, sound pressure levels ranging from 40 dB to 94 dB correspond to sound pressures ranging from 0.002 Pa to 1 Pa. A doubling of sound energy corresponds to an increase in level of 3 dB.
2.37 Sound Receiver — One or more observation points at which sound is evaluated or measured. The effect of sound on an individual receiver is usually evaluated by measurements near the ear or close to the body.
2.38 Sound Reduction Index, R — Laboratory measure of the sound insulating properties of a material or building element in a stated frequency band.
NOTE — For further information see Annex B.
2.39 Sound Source — Equipment or phenomena which generate sound. Source room is the room containing sound source.
2.40 Spectrum — A quantity expressed as a function of frequency, such as sound pressure versus frequency curve.
2.41 Standardized Impact Sound Pressure Level, L n T - Impact sound pressure level normalized to a reverberation time in the receiving room of 0.5 s.
NOTE — Standardized impact sound pressure level is used to characterize the insulation of floors in buildings against impact sound in a stated frequency band (see Annex B).
2.42 Speech Interference Level (SIL) — A descriptor for rating steady noise according to its ability to interfere with conversation between two people. SIL is the arithmetic average of the sound pressure levels in the three octave bands with centre frequencies at 500, 1 000 and 2 000 Hz.
2.43 Standardized Level Difference, D n T Difference in sound level between a pair of rooms, in a stated frequency band, normalized to a reverberation time of 0.5 s.
NOTE — Standardized level difference takes account of all sound transmission paths between the rooms (see Annex B).
2.44 Structure Borne Noise — Generation and propagation of time dependent motions and forces in solid materials which result in unwanted radiated sound.
2.45 Transient Sound — Sound which is audible for a limited period of time, for example sound from over flight of an airplane.
2.46 Third Octave Band — Band of frequencies in which the upper limit of the band is 2 ~ ~ 1 / 3 ~ times the frequency of the lower limit.
2.47 Threshold of Hearing — The lowest continuous sound pressure level which will create an auditory sensation for the average human ear. Any sound below these levels will be inaudible and any sound above the threshold will vary in loudness dependent on intensity.
2.48 Vibration Isolation — Reduction of force or displacement transmitted by a vibratory source, often attained by use of a resilient mount.
2.49 Wavelength — The length in space of one complete cycle of a sound wave.
2.50 Weighted Level Difference, D w — Singlenumber quantity that characterizes airborne sound insulation between rooms but which is not adjusted to reference conditions.
NOTE — Weighted level difference is used to characterize the insulation between rooms in a building as they are; values cannot normally be compared with measurements made under other conditions {see good practice [8-4(1)]}.
2.51 Weighted Sound Reduction Index, R _ w - Single number quantity which characterizes the airborne sound insulating properties of a material or building element over a range of frequencies.
NOTE — The weighted sound reduction index is used to characterize the insulation of a material or product that has been measured in a laboratory (see Annex B).
2.52 Weighted Standardized Impact Sound Pressure Level, L ~ n T , ~ w ~ - ~ ' Single number quantity used to characterize the impact sound insulation of floors over a range of frequencies.
NOTE — Weighted standardized impact sound pressure level is used to characterize the insulation of floors in buildings (see Annex B).
2.53 Weighted Standardized Level Difference, D n , T w Single-number quantity, which characterizes the airborne sound insulation between rooms
NOTE — Weighted standardized level difference is used to characterize the insulation between rooms in a building (see Annex B).
2.54 Weighted Normalized Impact Sound Pressure Level, L n , w ' — Single number quantity used to characterize the impact sound insulation of floors over a range of frequencies.
NOTE — Weighted normalized impact sound pressure level is usually used to characterize the insulation of floors tested in a laboratory (see Annex B).
2.55 White Noise — A noise whose spectrum (level) density is substantially independent of frequency over a specified range and has equal power for any range of frequencies of constant band width.
3 PLANNING AND DESIGN AGAINST OUTDOOR NOISE