b) The list at the end of this part has been completely reclassified to make it more user friendly and updated to reflect the latest available Indian Standard and methods of test.
A reference to SP 21 ‘Summaries of Indian Standards for building materials’ may be useful. This publication gives the summaries of Indian Standards covering various building materials, fittings and components except standards relating to paints.
All standards cross-referred to in the main text of this Part, are subject to revision. The parties to agreement based on this section are encouraged to investigate the possibility of applying the most recent editions of the standards.
1Scope
This Part of the Code covers the requirements of building materials and components, and criteria for accepting new or alternative building materials and components.
2Materials
Every material used in fulfilment of the requirements of this Part, unless otherwise specified in the Code or approved, shall conform to the relevant Indian Standards. A list of Indian Standards as the ‘accepted standards’ is given at the end of this Part of the Code. At the time of publication of the Code, the editions indicated were valid. All standards are subject to amendments and revisions. The Authority shall take cognizance of such amendments and revisions. The latest version of a standard shall, as far as possible, be adopted at the time of enforcement of this Part of the Code.
List of Standards
Following are the Indian Standards for various building materials and components, to be complied with in fulfillment of the requirements of the Code.
In the following list, while enlisting the Indian Standards, the materials have been categorized in such a way as to make the list user friendly. In the process, if so required, some of the standards have been included even in more than one category of products, such as in the category based on composition as well as on end application of the materials. The list has been arranged in alphabetical order of their principal category as given below:
IS No.
Title
733 : 1983
Specification for wrought aluminium and aluminium alloys, bars, rods and sections for general engineering purposes (third revision)
737 : 1986
Specification for wrought aluminium and aluminium alloys, sheet rods and strip for general engineering purposes (third revision)
1. ALUMINIUM AND OTHER LIGHT METALS AND THEIR ALLOYS
2. BITUMEN AND TAR PRODUCTS
3. BUILDER'S HARDWARES
738 : 1994
Specification for wrought aluminium and aluminium alloy drawn tube for general engineering purposes (third revision)
4. BUILDING CHEMICALS
5. BUILDING LIME AND PRODUCTS
6. BURNT CLAY PRODUCTS
7. CEMENT AND CONCRETE (including concrete reinforcement)
740 : 1977
Specification for wrought aluminium and aluminium alloy rivet stock for general engineering purposes (second revision)
712 : 1984 Specification for building limes (third revision)
1624 : 1986 Method of field testing of building lime (first revision)
2686 : 1977 Specification for cinder as fine aggregates for use in lime concrete (first revision)
3068 : 1986 Specification for broken brick (burnt-clay) coarse aggregates for use in lime concrete (second revision)
3115 : 1992 Specification for lime based blocks (second revision)
3182 : 1986 Specification for broken bricks (burnt clay) fine aggregates for use in lime mortar (second revision)
4098 : 1983 Specification for lime-pozzolana mixture (first revision)
4139 : 1989 Specification for calcium silicate bricks (second revision)
6932 Method of tests for building limes: (Part 1) : 1973 Determination of insoluble residue, loss on ignition, insoluble matter, silicon dioxide, ferric and aluminium oxide, calcium oxide and magnesium oxide
(Part 2) : 1973 Determination of carbon dioxide content
(Part 3) : 1973 Determination of residue on slaking of quicklime
(Part 4) : 1973 Determination of fineness of hydrated lime
(Part 5) : 1973 Determination of unhydrated oxide
IS No.
Title
IS No.
Title
(Part 6):1973
Determination of volume yield of quicklime
6165:1992
Dimensions for special shapes of clay bricks (first revision)
(Part 7):1973
Determination of compressive and transverse strength
11650:1991
Guide for manufacture of common burnt clay building bricks by semi-mechanized process (first revision)
(Part 8):1973
Determination of workability
(Part 9):1973
Determination of soundness
13757:1993
Specification for burnt clay fly ash building bricks
(Part 10):1973
Determination of popping and pitting of hydrated lime
d) Jallies
(Part 11):1984
Determination of setting time of hydrated lime
7556:1988
Specification for burnt clay jallies (first revision)
10360:1982
Specification for lime pozzolana concrete blocks for paving
e) Tiles
10772:1983
Specification for quick setting lime pozzolana mixture
654:1992
Specification for clay roofing tiles, Mangalore pattern (third revision)
12894:2002
Specification for pulverized fuel ash lime bricks (first revision)
1464:1992
Specification for clay ridge and ceiling tiles (second revision)
6. BURNT CLAY PRODUCTS
6. BURNT CLAY PRODUCTS
1478:1992
Specification for clay flooring tiles (second revision)
a) Blocks
2690
Specification for burnt clay flat terracing tiles:
3952:1988
Specification for burnt hollow bricks for walls and partitions (second revision)
(Part 1):1993
Machine made (second revision)
3952:1988
Specification for burnt hollow bricks for walls and partitions (second revision)
(Part 2):1992
Handmade (second revision)
b) Soil-Based Products
b) Soil-Based Products
3367:1993
Specification for burnt clay tiles for use in lining irrigation and drainage works (second revision)
1725:1982
Specification for soil-based blocks used in general building construction
3951
Specification for hollow clay tiles for floor and roofs:
c) Bricks
1077:1992
Specification for common burnt clay building bricks (fifth revision)
(Part 1):1975
Filler type (first revision)
1077:1992
Specification for common burnt clay building bricks (fifth revision)
(Part 2):1975
Structural type (first revision)
2117:1991
Guide for manufacture of hand-made-common burnt clay building bricks (third revision)
13317:1992
Specification for clay roofing camty tiles, half round and flat tiles
2180:1988
Specification for heavy duty burnt clay building bricks (third revision)
7. CEMENT AND CONCRETE (including concrete reinforcement)
7. CEMENT AND CONCRETE (including concrete reinforcement)
2222:1991
Specification for burnt clay perforated building bricks (fourth revision)
a) Aggregates
2691:1988
Specification for burnt clay facing bricks (second revision)
383:1970
Specification for coarse and fine aggregates from natural sources for concrete (second revision)
3495(Parts 1 to 4):1992
Methods of test of burnt clay building bricks (third revision)
1542:1992
Specification for sand for plaster (second revision)
3583:1988
Specification for burnt clay paving bricks (second revision)
2116:1980
Specification for sand for masonry mortars (first revision)
4885:1988
Specification for sewer bricks (first revision)
2386
Methods of test for aggregates for concrete:
5454:1978
Methods for sampling of clay building bricks
(Part 1):1963
Particle size and shape
5779:1986
Specification for burnt clay soling bricks (first revision)
(Part 2):1963
Estimation of deleterious materials and organic impurities
(Part 3):1963
Specific gravity, density, voids, absorption and bulking
IS No.
Title
IS No.
Title
(Part 4):1963
Mechanical properties
3812
Specification for pulverized fuel ash:
(Part 5):1963
Soundness
Specification for pulverized fuel ash:
(Part 6):1963
Measuring mortar making properties of fine aggregates
(Part 1):2003
For use as pozzolana in cement, cement mortar and concrete (second revision)
(Part 7):1963
Alkali aggregate reactivity
For use as pozzolana in cement, cement mortar and concrete (second revision)
(Part 8):1963
Petrographic examination
(Part 2):2003
For use as admixture in cement mortar and concrete (second revision)
2430:1986
Methods of sampling of aggregates of concrete (first revision)
For use as admixture in cement mortar and concrete (second revision)
6579:1981
Specification for coarse aggregate for water bound macadam (first revision)
6491:1972
Method of sampling of flyash
6579:1981
Specification for coarse aggregate for water bound macadam (first revision)
6925:1973
Methods of test for determination of water soluble chlorides in concrete admixtures
9142:1979
Specification for artificial lightweight aggregates for concrete masonry units
9103:1999
Specification for admixtures for concrete (first revision)
b) Cement
12089:1987
Specification for granulated slag for manufacture of Portland slag cement
269:1989
Specification for ordinary portland cement, 33 Grade (fourth revision)
Specification for granulated slag for manufacture of Portland slag cement
455:1989
Specification for Portland slag cement (fourth revision)
12870:1989
Methods of sampling calcined clay pozzolana
1489
Specification for Portland pozzolana cement:
15388:2003
Specification for silica fume
1489
Specification for Portland pozzolana cement:
d) Concrete
(Part 1):1991
Flyash based (third revision)
456:2000
Code of practice for plain and reinforced concrete (fourth revision)
(Part 2):1991
Calcined clay based (third revision)
Code of practice for plain and reinforced concrete (fourth revision)
3466:1988
Specification for masonry cement (second revision)
1343:1980
Code of practice for prestressed concrete (first revision)
6452:1989
Specification for high alumina cement for structural use (first revision)
4926:2003
Code of practice for ready-mixed concrete (third revision)
6909:1990
Specification for supersulphated cement
e) Cement and Concrete Sampling and Methods of Test
8041:1990
Specification for rapid hardening Portland cement (second revision)
516:1959
Methods of test for strength of concrete
8042:1989
Specification for white Portland cement (second revision)
1199:1959
Methods of sampling and analysis of concrete
8043:1991
Specification for hydrophobic Portland cement (second revision)
2770
Methods of testing bond in reinforced concrete: Part 1 Pullout test
8112:1989
Specification for 43 grade ordinary Portland cement (first revision)
(Part 1):1967
Methods of testing bond in reinforced concrete: Part 1 Pullout test
12269:1987
Specification for 53 grade ordinary Portland cement
3085:1965
Methods of test for permeability of cement mortar and concrete
12330:1988
Specification for sulphate resisting Portland cement
3535:1986
Methods of sampling hydraulic cement (first revision)
12600:1989
Specification for low heat Portland cement
4031
Methods of physical tests for hydraulic cement:
c) Mineral/Chemical Admixtures and Pozzolanas
c) Mineral/Chemical Admixtures and Pozzolanas
(Part 1):1996
Determination of fineness by dry sieving (second revision)
1344:1981
Specification for calcined clay pozzolana (second revision)
(Part 2):1999
Determination of fineness by specific surface by Blaine air permeability method (second revision)
1727:1967
Methods of test for pozzolanic materials (first revision)
Determination of fineness by specific surface by Blaine air permeability method (second revision)
IS No. Title
(Part 3) : 1988 Determination of soundness (first revision)
(Part 4) : 1988 Determination of consistency of standard cement paste (first revision)
(Part 5) : 1988 Determination of initial and final setting times (first revision)
(Part 6) : 1988 Determination of compressive strength of hydraulic cement (other than masonry cement) (first revision)
(Part 7) : 1988 Determination of compressive strength of masonry cement (first revision)
(Part 8) : 1988 Determination of transverse and compressive strength of plastic mortar using prism (first revision)
(Part 9) : 1988 Determination of heat of hydration (first revision)
(Part 10) : 1988 Determination of drying shrinkage (first revision)
(Part 11) : 1988 Determination of density (first revision)
(Part 12) : 1988 Determination of air content of hydraulic cement mortar (first revision)
(Part 14) : 1989 Determination of false set
(Part 15) : 1991 Determination of fineness by wet sieving
4032 : 1985 Methods of chemical analysis for hydraulic cement (first revision)
5816 : 1999 Method of test for splitting tensile strength of concrete (first revision)
8142 : 1976 Methods of test for determining setting time of concrete by penetration resistance
9013 : 1978 Method of making, curing and determining compressive strength of accelerated cured concrete test specimens
9284 : 1979 Method of test for abrasion resistance of concrete
12423 : 1988 Methods for colorometric analysis of hydraulic cement
12803 : 1989 Methods of analysis of hydraulic cement by X-ray fluorescence spectrometer
IS No. Title
12813 : 1989 Method of analysis of hydraulic cement by atomic absorption spectrophotometer
13311 Methods of non-destructive testing of concrete:
(Part 1) : 1992 Ultrasonic pulse velocity
(Part 2) : 1992 Rebound hammer
f) Treatment of Concrete Joints
1834 : 1984 Specification for hot applied sealing compound for joint in concrete (first revision)
1838 Specification for preformed fillers for expansion joint in concrete pavements and structures (non-extruding and resilient type):
(Part 2) : 1984 CNSL aldehyde resin and coconut pith
10566 : 1983 Methods of test for preformed fillers for expansion joints in concrete paving and structural construction
11433 Specification for one grade polysulphide based joint sealant:
(Part 1) : 1985 General requirements
(Part 2) : 1986 Methods of test
12118 Specification for two parts polysulphide based sealants:
(Part 1) : 1987 General requirements
(Part 2) : 1987 Methods of test
g) Concrete Reinforcement
432 Specification for mild steel and medium tensile steel bars and hard drawn steel wire for concrete reinforcement:
(Part 1) : 1982 Mild steel and medium tensile steel bars (third revision)
(Part 2) : 1982 Hard drawn steel wire (third revision)
1566 : 1982 Specification for hard drawn steel wire fabric for concrete reinforcement (second revision)
1608 : 1995 Mechanical testing of materials — Tensile testing
1785 Specification for plain hard drawn steel wire for prestressed concrete:
IS No.
Title
IS No.
Title
(Part 1): 1983
Cold drawn stress-relieved wire (second revision)
6073: 1971
Specification for autoclaved reinforced cellular concrete floor and roof slabs
(Part 2): 1983
As drawn wire (first revision)
1786: 1985
Specification for high strength deformed steel bars and wires for concrete reinforcement (third revision)
6441
Methods of test for autoclaved cellular concrete products:
(Part 1): 1972
Determination of unit weight or bulk density and moisture content
2090: 1983
Specification for high tensile steel bars used in prestressed concrete (first revision)
(Part 2): 1972
Determination of drying shrinkage
(Part 4): 1972
Corrosion protection of steel reinforcement in autoclaved cellular concrete
6003: 1983
Specification for indented wire for prestressed concrete (first revision)
(Part 5): 1972
Determination of compressive strength
6006: 1983
Specification for uncoated stress-relieved strand for prestressed concrete (first revision)
(Part 6): 1973
Strength, deformation and cracking of flexural members subject to bending-short duration loading test
10790
Methods of sampling of steel for prestressed and reinforced concrete:
(Part 7): 1973
Strength, deformation and cracking of flexural members subject to bending-sustained loading test
(Part 1): 1984
Prestressing steel
(Part 8): 1973
Loading tests for flexural members in diagonal tension
(Part 2): 1984
Reinforcing steel
13620: 1993
Specification for fusion bonded epoxy coated reinforcing bars
(Part 9): 1973
Jointing of autoclaved cellular concrete elements
iii) Other Fibre Cement Products
14862 : 2000 Specification for fibre cement flat sheets
14871 : 2000 Specification for products in fibre reinforced cement long corrugated or asymmetrical section sheets and fittings for roofing and cladding
iv) Concrete Pipes and Pipes Lined/Coated with Concrete or Mortar
458 : 2003 Specification for precast concrete pipes (with and without reinforcement) (fourth revision)
427 : 1965 Specification for distemper, dry, colour as required (revised)
428 : 2000 Specification for distemper, washable (second revision)
5410 : 1992 Specification for cement paint, colour as required (first revision)
5411 Specification for plastic emulsion paint:
(Part 1) : 1974 For interior use (first revision)
(Part 2) : 1972 For exterior use
b) Ready Mixed Paints, Enamels and Powder Coatings
101 Methods of sampling and test for paints, varnishes and related products:
(Part 1/Sec 1) : Test on liquid paints (general 1986 and physical), Section 1 Sampling (third revision)
(Part 1/Sec 2) : Test on liquid paints (general 1987 and physical), Section 2 Preliminary examination and preparation of samples for testing (third revision)
(Part 1/Sec 3) : Test on liquid paints (general and 1986 physical), Section 3 Preparation of panels (third revision)
(Part 1/Sec 4) : Test on liquid paints (general and 1987 physical), Section 4 Brushing test (third revision)
(Part 1/Sec 5) : Test on liquid paints (general and 1989 physical), Section 5 Consistency (third revision)
(Part 1/Sec 6) : Test on liquid paints (general and 1987 physical), Section 6 Flash point (third revision)
IS No. Title
(Part 1/Sec 7) : Test on liquid paints (general and 1987 physical), Section 7 Mass per 10 litres (third revision)
(Part 2/Sec 1) : Test on liquid paints (chemical 1988 examination), Section 1 Water content (third revision)
(Part 2/Sec 2) : Test on liquid paints (chemical 1986 examination), Section 2 Volatile matter (third revision)
(Part 3/Sec 1) : Tests on paint film formation, 1986 Section 1 Drying time (third revision)
(Part 3/Sec 2) : Tests on paint film formation, 1989 Section 2 Film thickness (third revision)
(Part 3/Sec 4) : Tests on paint film formation, 1987 Section 4 Finish (third revision)
(Part 3/Sec 5) : Tests on paint film formation, 1987 Section 5 Fineness of grind (third revision)
Specification for vitreous enamelled steel kitchen sinks
14643 : 1999
Specification for unsintered polytetrafluoroethylene (PTFE) tape for thread sealing applications
8727 : 1978
Specification for vitreous enamelled steel wash basins
14706 : 1999
Sampling and preparation of test specimen of geotextiles
9140 : 1996
Method of sampling of vitreous and fire clay sanitary appliances (second revision)
14714 : 1999
Determination of abrasion resistance of geotextiles
12701 : 1996
Specification for rotational moulded polyethylene water storage tanks (first revision)
14715 : 2000
Specification for woven jute geotextiles
13983 : 1994
Specification for stainless steel sinks for domestic purposes
14716 : 1999
Determination of mass per unit area of geotextiles
14399
Hot press moulded thermosetting glass fibre reinforced (GRP) sectional water storage tanks:
14739 : 1999
Methods for determination of creep of geotextiles
(Part 1) : 1996
Specification for panels
14753 : 1999
Specification for poly (methyl) methacrylate (PMMA) (Acrylic) sheets
(Part 2) : 1996
Guidelines for assembly, installation and testing
14986 : 2001
Jute geo-grid for rain water erosion control in road and railway embankments and hill slopes
b) Pipes and Fittings Excluding Valves
b) Pipes and Fittings Excluding Valves
14986 : 2001
Jute geo-grid for rain water erosion control in road and railway embankments and hill slopes
i) Brass and Copper Pipes and Fittings
i) Brass and Copper Pipes and Fittings
IS No.
Title
IS No.
Title
(Part 2): 2003
Specific requirements for 90° bends (first revision)
12235
Methods of test for unplasticized PVC pipes for potable water supplies:
(Part 3): 2003
Specific requirements for 90° tees
(Part 4): 2003
Specific requirements for reducers
(Part 1): 1986
Method of measurement of outside diameter
(Part 5): 2003
Specific requirements for ferrule reducers (first revision)
(Part 2): 1986
Measurement of wall thickness
(Part 6): 2003
Specific requirements for pipe ends
(Part 3): 1986
Test for opacity
(Part 7): 2003
Specific requirements for sandwich flanges
(Part 4): 1986
Determining the detrimental effect on the composition of water
(Part 8): 2003
Specific requirements for reducing tests
(Part 5): 1986
Reversion test
(Part 9): 2003
Specific requirements for end caps (first revision)
(Part 6): 1986
Stress relief test
8360
Specification for fabricated high density polyethelene (HDPE) fittings for potable water supplies:
(Part 7): 1986
Test for resistance to sulphuric acid
(Part 8): 1986
Internal hydrostatic pressure test
(Part 9): 1986
Impact strength test
(Part 10): 1986
Method for determination of organotin as tin aqueous solution
(Part 1): 1977
General requirements
(Part 11): 1986
Extractability of cadmium and mercury occurring as impurities
(Part 2): 1977
Specific requirements for 90° tees
(Part 3): 1977
Specific requirements for 90° bends
12709: 1994
Specification for glass-fibre reinforced plastic (GRP) pipes joints and fittings for use for potable water supply (first revision)
10124
Specification for fabricated PVC fittings for potable water supplies:
(Part 1): 1988
General requirements (first revision)
12818: 1992
Specification for unplasticized PVC screen and casing pipes for bore/tubewell (first revision)
(Part 2): 1988
Specific requirements for sockets (first revision)
IS No. Title
vi) Steel Tubes, Pipes and Fittings 1239 Mild steel tubes, tubular and other wrought steel fittings: (Part 1) : 1990 Mild steel tubes (fifth revision)
(Part 2): 1992 Mild steel tubular and other wrought steel pipe fittings (third revision)
3589:1991 Specification for seamless or electrically welded steel pipes for water, gas and sewage (168.3 to 2 032 mm outside size) (second revision)
4270:1992 Steel tubes used for water wells (second revision)
5504:1997 Specification for spiral welded pipes (first revision)
6286:1979 Seamless and welded steel pipe for sub-zero temperature service
6392: 1971 Steel pipe flanges
vii) Stoneware Pipes and Fittings
651: 1992 Specification for salt-glazed stoneware pipes and fittings (fifth revision)
3006:1979 Specification for chemically resistant glazed stoneware pipes and fittings (first revision)
viii) Asbestos Cement Pipes [See 8 (a) (ii) under the category Composite Matrix Products']
ix) Concrete Pipes and Pipes Lined/Coated with Concrete or Mortar [See 8 (a) (iv) under the category 'Composite Matrix Products']
c) Kitchen and Sanitary Appliances
771 Specification for glazed fire clay sanitary appliances:
(Part 1) : 1979 General requirements (second revision)
(Part 2) : 1985 Specific requirements of kitchen and laboratory sinks (third revision)
(Part 3/Sec 1) : Specific requirements of urinals, 1979 Section 1 Slab urinals (second revision)
(Part 3/Sec 2) : Part 3Specific requirements of 1985 urinals, Section 2 Stall urinals (third revision)
IS No. Title
(Part 4) : 1979 Specific requirements of post mortom slabs (second revision)
(Part 5) : 1979 Specific requirements of shower trays (second revision)
(Part 6) : 1979 Specific requirements of bed-pan sinks (second revision)
(Part 7):1981 Specific requirements of slop sinks (second revision)
772:1973 Specification for general requirements of enamelled cast iron sanitary appliances (second revision)
773:1988 Specification for enamelled cast iron water-closets railway stock type (fourth revision)
774:1984 Specification for flushing cisterns for water-closets and urinals (other than plastic cisterns) (fourth revision)
1726:1991 Specification for cast iron manhole covers and frames (third revision)
2326:1987 Specification for automatic flushing cisterns for urinals (second revision)
2548 Specification for plastic seats and covers for water-closets:
(Part 1) : 1996 Thermoset seats and covers (fifth revision)
(Part 2) : 1996 Thermoplastic seats and covers (fifth revision) 2556 Specification for vitreous sanitary appliances (vitreous china):
(Part 1): 1994 General requirements (third revision)
(Part 2) : 1994 Specific requirements of washdown water-closets (fourth revision)
(Part 3) : 1994 Specific requirements of squatting pans (fourth revision)
(Part 4) : 1994 Specific requirementsof wash basins (third revision)
(Part 5) : 1994 Specific requirements of laboratory sinks (third revision)
(Part 6) : 1995 Specific requirements of urinals and partition plates (fourth revision)
(Part 7) : 1995 Specific requirements of accessories for sanitary appliances (third revision)
(Part 8) : 1995 Specific requirements of siphonic wash-down water closets (fourth revision)
IS No.
Title
IS No.
Title
(Part 9):1995
Specific requirements of bidets (fourth revision)
3950:1979
Specification for surface boxes for sluice valves (first revision)
(Part 14):1995
Specific requirements of integrated squatting pans (first revision)
20 Soil-based Products
1725 : 1982 Specification for soil-based blocks used in general building construction
10Doors, Windows and Ventilators
a) Wooden Doors, Windows and Ventilators
1003 Specification for timber panelled and glazed shutters:
(Part 1) : 2003 Door shutters (fourth revision)
(Part 2) : 1994 Window and ventilator shutters (third revision)
1826 : 1961 Specification for venetian blinds for windows
(Part 1) : 1983 Plywood face panels (fourth revision)
(Part 2) : 1983 Particle board face panels and hardboard face panels (third revision) 2202 Specification for wooden flush door shutters (solid core type):
(Part 1) : 1991 Plywood face panels (fifth revision)
(Part 2) : 1983 Particle board face panels and hardboard face panels (third revision)
4020 Method of tests for door shutters:
(Part 1) : 1998 General (third revision)
(Part 2) : 1998 Measurement of dimensions and squareness (third revision)
(Part 3) : 1998 Measurement of general flatness (third revision)
(Part 4) : 1998 Local planeness test (third revision)
(Part 5) : 1998 Impact indentation test (third revision)
IS No. Title
(Part 6) : 1998 Flexure test (third revision)
(Part 7) : 1998 Edge loading test (third revision)
(Part 8) : 1998 Shock resistance test (third revision)
(Part 9) : 1998 Buckling resistance test (third revision)
(Part 10) : 1998 Slamming test (third revision)
(Part 11) : 1998 Misuse test (third revision)
(Part 12) : 1998 Varying humidity test (third revision)
(Part 13) : 1998 End immersion test (third revision)
(Part 14) : 1998 Knife test (third revision)
(Part 15) : 1998 Glue adhesion test (third revision)
(Part 16) : 1998 Screw withdrawal resistance test (third revision)
4021 : 1995 Specification for timber door, window and ventilator frames
4962 : 1968 Specification for wooden side sliding doors
6198 : 1992 Specification for ledged, braced and battened timber shutters (second revision)
b) Metal Doors, Windows Frames and Ventilators
1038 : 1983 Specification for steel doors, windows and ventilators (third revision)
1361 : 1978 Specification for steel windows for industrial buildings (first revision)
1948 : 1961 Specification for aluminium doors, windows and ventilators
1949 : 1961 Specification for aluminium windows for industrial buildings
4351 : 2003 Specification for steel door frames (second revision)
6248 : 1979 Specification for metal rolling shutters and rolling grills (first revision)
7452 : 1990 Specification for hot rolled steel sections for doors, windows and ventilators (second revision)
3438 : 1994 Specification for silvered glass mirrors for general purposes (second revision)
5437 : 1994 Specification for figured rolled and wired glass (first revision)
14900 : 2000 Specification for transparent float glass
26Unit Weights of Building Materials
IS No. Title
875 (Part 1) : Code of practice for design loads 1987 (other than earthquake) for buildings and structures: Part 1 Dead loads — Unit weights of building material and stored materials (second revision)
WATERPROOFING AND DAMP-PROOFING MATERIALS
1322 : 1993 Specification for bitumen felts for waterproofing and damp-proofing (fourth revision)
1580 : 1991 Specification for bituminous compound for waterproofing and caulking purposes (first revision)
3037 : 1986 Specification for bitumen mastic for use in waterproofing of roofs (first revision)
3384 : 1986 Specification for bitumen primer for use in waterproofing and dampproofing (first revision)
5871 : 1987 Specification for bitumen mastic for tanking and damp-proofing (first revision)
7193 : 1994 Specification for glass fibre base coal tar pitch and bitumen felts (first revision)
12027 : 1987 Specification for silicone-based water repellents
13435 Method of tests for acrylic based waterproofing material:
(Part 1) : 1992 Determination of solid content
(Part 2) : 1992 Determination of coarse particle
(Part 4) : 1993 Pressure head test
(Part 5) : 1993 Heat resistance test
(Part 6) : 1993 Water absorption test
(Part 7) : 1993 Determination of binder content
14695 : 1999 Specification for glass fibre base coal tar pitch outer wrap
28Welding Electrodes and Wires
814 : 1991 Specification for covered electrodes for manual metal arc welding of carbon and carbon manganese steel (fifth revision)
1278 : 1972 Specification for filler rods and wires for gas welding (second revision)
1395 : 1982 Specification for low and medium alloy steel covered electrodes for manual metal arc welding (third revision)
2879 : 1998 Mild steel for metal arc welding electrodes (third revision)
3613 : 1974 Acceptance tests for wire flux combinations for submerged-arc welding of structural steel (first revision)
4972 : 1968 Specification for resistance spotwelding electrodes
5206 : 1983 Covered electrodes for manual arc welding of stainless steel and other similar high alloy steels (first revision)
5511 : 1991 Specification for covered electrodes for manual metal arc welding of cast iron (first revision)
5897 : 1985 Specification for aluminium and aluminium alloy welding rods and wires and magnesium alloy welding rods (first revision)
(Part 3) : 1992 Determination of capillary water 5898 : 1970 Specification for copper and take-up copper alloy bare solid welding rods and electrodes (Part 4) : 1992 (Part 4) : 1992 Determination of pH value Determination of pH value
6419 : 1996 Specification for welding rods and (Part 5) : 1992 Determination of minimum film bare electrodes for gas shielded arc forming temperature and white welding of structural steel (first point 1382 D: revision)
(Part 1) : 1993 Breaking strength test
(Part 2) : 1993 Pliability test
(Part 3) : 1993 Storage sticking test
6560 : 1996 Specification for molybdenum and chromium-molybdenum low alloy steel welding rods and bare electrodes for gas shielded arc welding (first revision)
IS No.
Title
IS No.
Title
7280 : 1974
Specification for bare wire electrodes for submerged-arc welding of structural steels
2266 : 2002
Specification for steel wire ropes for general engineering purposes (fourth revision)
8363 : 1976
Specification for bare wire electrodes for electroslag welding of steels
2365 : 1977
Specification for steel wire suspension ropes for lifts, elevators and hoists (first revision)
10631 : 1983
Stainless steel for welding electrode core wire
2721 : 2003
Specification for galvanized steel wire chain link fences fabric (second revision)
29. WIRE ROPES AND WIRE PRODUCTS
278 : 1978
Specification for galvanized steel barbed wire for fencing (third revision)
6594 : 1977
Specification for technical supply conditions for wire ropes and strands (first revision)
2140 : 1978
Specification for stranded galvanized steel wire for fencing (first revision)
12776 : 2002
Specification for galvanized strand for earthing (first revision)
PART 10 LANDSCAPING, SIGNS AND OUTDOOR DISPLAY STRUCTURES
Section 1 Landscape Planning and Design
BUREAU OF INDIAN STANDARDS
FOREWORD
... 3
1 SCOPE
... 5
2 TERMINOLOGY
... 5
3 PERMIT
... 6
4 PROTECTION OF LANDSCAPE DURING CONSTRUCTION
... 8
5 SOIL AND WATER CONSERVATION
... 9
6 EARTH SLOPES AND GRADING REQUIREMENTS
... 12
7 PLANTING DESIGN CONSIDERATIONS
... 13
8 SPECIFICATIONS FOR PLANTING WORKS
... 20
9 SERVICE UTILITIES IN LANDSCAPE
... 24
10 PAVED SURFACES IN EXTERNAL AREAS
... 26
11 STREET FURNITURE
... 26
National Building Code Sectional Committee, CED 46
This Part of the Code was first published in 1970 and subsequently revised in 1983, and covered provisions relating to only signs and outdoor display structures. In this revision, this Part has been sub-divided into two sections as follows by including a new section on landscaping:
Section 1 Landscape planning and design
Section 2 Signs and outdoor display structures
This Section covers the requirement of landscape planning and design with the aim of improving quality of outdoor built environment and protection of the land and its resources. With growing urban development and environmental degradation it has become imperative to determine landscape design parameters, and also provide rules, regulations, controls and procedures for the protection, preservation and modification of surrounding environment. A brief clause on street furniture has also been introduced in this Section.
The components of landscape design and external development were earlier covered in the Code in its various Parts/Sections but a comprehensive treatment has been given in this new Section in this revision.
21Steel and Its Alloys
a) General
1030 : 1998 Carbon steel castings for general engineering purposes (fifth revision)
1136 : 1990 Preferred sizes for wrought metal products (first revision)
1137 : 1990 Thickness of sheet and diameters of wire (first revision)
1762 (Part 1) : Code for designation of steels: 1974 Part 1 Based on letter symbols (first revision)
2049 : 1978 Colour code for the identification of wrought steel for general engineering purposes (first revision)
2644 : 1994 High tensile steel castings (fourth revision)
7598 : 1990 Classification of steels (first revision)
2062 : 1999 Specification for steel for general structural purposes (fifth revision)
2830 : 1992 Specification for carbon steel billets ingots, blooms and slabs for re-rolling into steel for general structural purposes (second revision)
2831 : 2000 Specification for carbon steel billets ingots, blooms and slabs for re-rolling into low tensile structural steel (third revision)
8053 : 1976 Specification for steel ingots and billets for the production of steel wire for the manufacture of wood screws
IS No. Title
8500 : 1991 Specification for structural steels microalloyed (medium and high strength qualities)
8952 : 1995 Steel ingots, blooms and billets for production of mild steel wire rods for general engineering purposes (first revision)
9467 : 1980 Steel ingots and billets for production of rivet bars for structural purposes
c) Sheet and Strip
277 : 2003 Specification for galvanized steel sheets (plain and corrugated) (sixth revision)
412 : 1975 Specification for expanded metal steel sheets for general purposes (second revision)
513 : 1994 Specification for cold rolled low carbon steel sheets and strips (fourth revision)
1079 : 1994 Specification for hot rolled carbon steel sheet and strip (fifth revision)
13008 : 1990 Specification for shallow corrugated asbestos cement sheets
(Part 8/Sec 6):1993
Tests for pigments and other solids, Section 6 Volume solids
(Part 9/Sec 1):1993
Tests for lacquers and varnish, Section 1 Acid value
3536:1999
Specification for ready mixed paint, brushing, wood primer (first revision)
(Part 9/Sec 2):1993
Tests for lacquers and varnish, Section 2 Rosin test
3537:1966
Specification for ready mixed paint, finishing, interior for general purposes, to Indian Standard colours No. 101, 216, 217, 219, 275, 281, 352, 353, 358 to 361, 363, 364, 388, 410, 442, 444, 628, 631, 632, 634, 693, 697, white and black
Specification for ready mixed paint, brushing, priming, plaster to Indian Standard colours No. 361 and 631 (first revision)
3539:1966
Specification for ready mixed paint, undercoating, for use under oil finishes, to Indian Standard colours, as required
123:1962
Specification for ready mixed paint, brushing, finishing, semi-gloss, for general purposes, to Indian Standard colours No. 445, 446, 448, 449, 451 and 473; and red oxide (colour unspecified) (revised)
3585:1966
Specification for ready mixed paint, aluminium, brushing, priming, water resistant, for wood work
3678 : 1966
Specification for ready mixed paint, thick white, for lettering
18. POLYMERS, PLASTICS AND GEOSYNTHETICS/GEOTEXTILES
18. POLYMERS, PLASTICS AND GEOSYNTHETICS/GEOTEXTILES
8662 : 1993
Specification for enamel, synthetic, exterior, (a) undercoating, (b) finishing, for railway coaches (first revision)
1998 : 1962
Methods of test for thermosetting synthetic resin bonded laminated sheets
9862 : 1981
Specification for ready mixed paint, brushing, bituminous black lead free, acid, alkali, water and chlorine resisting
2036 : 1995
Specification for phenolic laminated sheets (second revision)
9862 : 1981
Specification for ready mixed paint, brushing, bituminous black lead free, acid, alkali, water and chlorine resisting
Specification for ready mixed paint, brushing, red oxide, priming for metals
2076 : 1981
Specification for unsupported flexible vinyl film and sheeting (first revision)
13183 : 1991
Specification for aluminium paints, heat resistant
2508 : 1984
Specification for low density polyethylene films (second revision)
13213 : 1991
Specification for polyurethane full gloss enamel (two pack)
2508 : 1984
Specification for low density polyethylene films (second revision)
13607 : 1992
Specification for ready mixed paint, finishing, general purposes, synthetic
6307 : 1971
Specification for rigid PVC sheets
13607 : 1992
Specification for ready mixed paint, finishing, general purposes, synthetic
9766 : 1992
Specification for flexible PVC compound (first revision)
13871 : 1993
Specification for powder coatings
10889 : 1984
Specification for high density polyethylene films
c) Thinners and Solvents
c) Thinners and Solvents
c) Thinners and Solvents
c) Thinners and Solvents
82 : 1992
Methods of sampling and test for thinners and solvents for paints (first revision)
12830 : 1989
Specification for rubber based adhesives for fixing PVC tiles to cement
324 : 1959
Specification for ordinary denatured spirit (revised)
13162
Methods of test for geotextiles:
324 : 1959
Specification for ordinary denatured spirit (revised)
(Part 2) : 1991
Determination of resistance to exposure of ultra-violet light and water (Xenon arc type apparatus)
533 : 1998
Specification for gum spirit of turpentine (oil of turpentine) (second revision)
(Part 3) : 1992
Determination of thickness at specified pressure
14314 : 1995
Specification for thinner general purposes for synthetic paints and varnishes
(Part 4) : 1992
Determination of puncture resistance by falling cone method
14314 : 1995
Specification for thinner general purposes for synthetic paints and varnishes
(Part 5) : 1992
Determination of tensile properties using a wide width strip
d) Varnishes and Lacquers
d) Varnishes and Lacquers
d) Varnishes and Lacquers
d) Varnishes and Lacquers
337 : 1975
Specification for varnish, finishing, interior (first revision)
13262 : 1992
Specification for pressure sensitive adhesive tapes with plastic base
347 : 1975
Specification for varnish, shellac, for general purposes (first revision)
13325 : 1992
Method of test for the determination to tensile properties of extruded polymer geogrids using the wide strip
348 : 1968
Specification for French polish (first revision)
13326 (Part 1) : 1992
Method of test for the evaluation of interface friction between geosynthetics and soil: Part 1 Modified direct shear technique
524 : 1983
Specification for varnish, finishing, exterior, synthetic (second revision)
13326 (Part 1) : 1992
Method of test for the evaluation of interface friction between geosynthetics and soil: Part 1 Modified direct shear technique
525 : 1968
Specification for varnish, finishing, exterior and general purposes (first revision)
14182 : 1994
Specification for solvent cement for use with unplasticized polyvinylchloride plastic pipe and fittings
642 : 1963
Specification for varnish medium for aluminium paint (revised)
14182 : 1994
Specification for solvent cement for use with unplasticized polyvinylchloride plastic pipe and fittings
15060 : 2001
Tensile test for joints/seams by wide width method of geotextiles
407 : 1981
Specification for brass tubes for general purposes (third revision)
15060 : 2001
Tensile test for joints/seams by wide width method of geotextiles
2501 : 1995
Specification for solid drawn copper tubes for general engineering purposes (third revision)
19. SANITARY Fittings
APPLIANCES AND WATER
a) General
ii) Cast Iron Pipes and Fittings
ii) Cast Iron Pipes and Fittings
775 : 1970
Specification for cast iron brackets and supports for wash basins and sinks (second revision)
1536 : 2001
Specification for centrifugally cast (spun) iron pressure pipes for water, gas and sewage (fourth revision)
782 : 1978
Specification for caulking lead (third revision)
1537 : 1976
Specification for vertically cast iron pressure pipes for water, gas and sewage (first revision)
804 : 1967
Specification for rectangular pressed steel tanks (first revision)
1538 : 1993
Specification for cast iron fittings for pressure pipes for water, gas and sewage (third revision)
1700 : 1973
Specification for drinking fountains (first revision)
1729 : 2002
Specification for sand cast iron spigot and socket soil, waste and ventilating pipes, fittings and accessories (second revision)
2963 : 1979
Specification for copper alloy waste fittings for wash-basins and sinks (first revision)
3489 : 1985
Specification for enamelled steel bath tubs (first revision)
IS No.
Title
IS No.
Title
1879 : 1987
Specification for malleable cast iron pipe fittings (second revision)
12988 : 1991
Rubber sealing rings for CID joints for light duty AC pipes — Dimensional requirements
3486 : 1966
Specification for cast iron spigot and socket drain pipes
13382 : 1992
Cast iron specials for mechanical and push on flexible joints for pressure pipelines for water, gas and sewage
3989 : 1984
Specification for centrifugally cast (spun) iron spigot and socket soil, waste and ventilating pipes, fittings and accessories (second revision)
5531 : 1988
Specification for cast iron specials for asbestos cement pressure pipes for water, gas and sewage (second revision)
404 (Part 1) : 1993
Specification for lead pipes: Part 1 For other than chemical purpose (third revision)
6163 : 1978
Specification for centrifugally cast (spun) iron low pressure pipes for water, gas and sewage (first revision)
iv) Fibre Pipes and Fittings
iv) Fibre Pipes and Fittings
6163 : 1978
Specification for centrifugally cast (spun) iron low pressure pipes for water, gas and sewage (first revision)
11925 : 1986
Specification for pitch-impregnated fibre pipes and fittings for drainage purposes
6418 : 1971
Specification for cast iron and malleable cast iron flanges for general engineering purposes
v) Plastic Pipes and Fittings
v) Plastic Pipes and Fittings
6418 : 1971
Specification for cast iron and malleable cast iron flanges for general engineering purposes
3076 : 1985
Specification for low density polyethylene pipes for potable water supplies (second revision)
7181 : 1986
Specification for horizontally cast iron double flanged pipes for water, gas and sewage (first revision)
4984 : 1995
Specification for high density polyethylene pipes for water supply (fourth revision)
8329 : 2000
Specification for centrifugally cast (spun) ductile iron pressure pipes for water, gas and sewage (third revision)
4985 : 2000
Specification for unplasticized PVC pipes for potable water supplies (third revision)
8794 : 1988
Specification for cast iron detachable joints for use with asbestos cement pressure pipes (first revision)
7834
Specification for injection moulded PVC socket fittings with solvent cement joints for water supplies:
9523 : 1980
Specification for ductile iron fittings for pressure pipes for water, gas and sewage
(Part 1) : 1987
General requirements (first revision)
9523 : 1980
Specification for ductile iron fittings for pressure pipes for water, gas and sewage
(Part 2) : 1987
Specific requirements for 45° elbows (first revision)
10292 : 1988
Dimensional requirements for rubber sealing rings for CID joints in asbestos cement piping (first revision)
(Part 3) : 1987
Specific requirements for 90° elbows (first revision)
10292 : 1988
Dimensional requirements for rubber sealing rings for CID joints in asbestos cement piping (first revision)
(Part 4) : 1987
Specific requirements for 90° tees (first revision)
10299 : 1982
Cast iron saddle pieces for service connection from asbestos cement pressure pipes
(Part 5) : 1987
Specific requirements for 45° tees (first revision)
11606 : 1986
Methods of sampling cast iron pipes and fittings
(Part 6) : 1987
Specific requirements for sockets (first revision)
12820 : 1989
Dimensional requirements of rubber gaskets for mechanical joints and push on joints for use with cast iron pipes and fittings for carrying water, gas and sewage
(Part 7) : 1987
Specific requirements for unions (first revision)
12820 : 1989
Dimensional requirements of rubber gaskets for mechanical joints and push on joints for use with cast iron pipes and fittings for carrying water, gas and sewage
(Part 8) : 1987
Specific requirements for caps (first revision)
12987 : 1991
Cast iron detachable joints for use with asbestos cement pressure pipes (light duty)
8008
Specification for injection moulded high density polyethylene (HDPE) fittings for potable water supplies:
12987 : 1991
Cast iron detachable joints for use with asbestos cement pressure pipes (light duty)
(Part 1) : 2003
General requirements
(Part 3): 1988
Specific requirements of straight reducers (first revision)
13592: 1992
Specification for UPVC pipes for soil and waste discharge systems inside buildings including ventilation and rainwater system
(Part 4): 1988
Specific requirements for caps (first revision)
14333: 1996
Specification for high density polyethylene pipes for sewerage
(Part 5): 1988
Specific requirements for equal tees (first revision)
14402: 1996
Specification for GRP pipes, joints and fittings for use for sewerage, industrial waste and water (other than potable)
(Part 6): 1988
Specific requirements for flanged tail piece with metallic flanges (first revision)
(Part 7): 1988
Specific requirements for threaded adaptors (first revision)
14735: 1999
Specification for unplasticized polyvinyl chloride (UPVC) injection moulded fittings for soil and waste discharge system for inside buildings including ventilation and rain water system
(Part 8): 1988
Specific requirements for 90° bends (first revision)
(Part 9): 1988
Specific requirements for 60° bends (first revision)
14885: 2001
Specification for polyethylene pipe for supply of gaseous fuel
(Part 10): 1988
Specific requirements for 45° bends (first revision)
15225: 2002
Specification for chlorinated polyvinyl chloride compounds used for pipes and fittings
(Part 11): 1988
Specific requirements for 30° bends (first revision)
(Part 12): 1988
Specific requirements for 221⁄2° bends (first revision)
15328: 2003
Specification for unplasticized non-pressure polyvinyl chloride (PVC-U) pipes for use in underground drainage and sewerage system
(Part 13): 1988
Specific requirements for 111⁄4° bends (first revision)
4038:1986
Specification for foot valves for water works purposes (second revision)
(Part 15):1995
Specific requirements of universal water closets (first revision)
4346:1982
Specification for washers for use with fittings for water services (first revision)
(Part 16):2002
Specific requirements for wash down wall mounted water-closets
(Part 17):1995
Specific requirements for wall mounted bidets
5312
Specification for swing check type reflux (non-return) valves:
5961:1970
Specification for cast iron gratings for drainage purposes
(Part 1):1984
Single door pattern (first revision)
(Part 2):1986
Multi-door pattern
7231:1984
Specification for plastic flushing cisterns for water-closets and urinals (second revision)
8931:1993
Specification for cast copper alloy fancy single tap combination tap and stop valves for water services (first revision)
(Part 1/Sec 2) : Gujarat state, Section 2 Engineering 1975 properties of building stones
2678 : 1987
Dimensions and tolerances for wrought aluminium and aluminium alloys, drawn round tubes (second revision)
9489 : 1980
Method of test for thermal conductivity of materials by means of heat flow meter
3577 : 1992
Dimensions and tolerances for wrought aluminium and aluminium alloys rivet, bolt and screw stock (first revision)
9490 : 1980
Method of determination for thermal conductivity of insulation materials (water calorimeter method)
3965 : 1981
Dimensions for wrought aluminium and aluminium alloys, bar, rod and section (first revision)
9742 : 1993
Specification for sprayed mineral wool thermal insulation (first revision)
6477 : 1983
Dimensions for wrought aluminium and aluminium alloys, extruded hollow sections
9743 : 1990
Specification for thermal insulation finishing cements (first revision)
12778 : 1989
Dimensions for hot rolled steel parallel flange beam and column sections
9842 : 1994
Specification for preformed fibrous pipe insulation (first revision)
11128 : 1994
Specification for spray applied hydrated calcium silicate thermal insulation
24. THERMAL INSULATION MATERIALS
3144 : 1992
Methods of test for mineral wool thermal insulation material (second revision)
11129 : 1984
Method of test for tumbling friability of preformed block-type thermal insulation
3346 : 1980
Methods for the determination of thermal conductivity of thermal insulation materials (two slab, guarded hot-plate method) (first revision)
11239
Method of test for rigid cellular thermal insulation materials:
(Part 1) : 1985
Dimensions
(Part 2) : 1985
Apparent density
(Part 3) : 1985
Dimensional stability
3677 : 1985
Specification for unbonded rock and slag wool for thermal insulation (second revision)
(Part 4) : 1985
Water vapour transmission rate
(Part 5) : 1985
Volume percent of open and closed cells
4671 : 1984
Specification for expanded polystyrene for thermal insulation purposes (first revision)
(Part 6) : 1985
Heat distortion temperature
(Part 7) : 1985
Coefficient of linear thermal expansion at low temperatures
5688 : 1982
Methods of test for preformed block-type and pipe-covering type thermal insulation (first revision)
(Part 8) : 1985
Flame height, time of burning and loss of mass
5724 : 1970
Methods of test for thermal insulating cement
(Part 9) : 1985
Water absorption
(Part 10) : 1985
Flexural strength
6598 : 1972
Specification for cellular concrete for thermal insulation
(Part 11) : 1985
Compressive strength
(Part 12) : 1989
Horizontal burning characteristics
7509 : 1993
Specification for thermal insulating cement (first revision)
(Part 13) : 1992
Determination of flammability by oxygen index
8154 : 1993
Specification for preformed calcium silicate insulation for temperature up to 650°C) (first revision)
11307 : 1985
Specification for cellular glass block and pipe thermal insulating
8183 : 1993
Specification for bonded mineral wool (first revision)
11308 : 1985
Specification for thermal insulating castables (hydraulic setting) for temperatures up to 1 250°C
IS No. Title
12436 : 1988 Specification for preformed rigid polyurethane (PUR) and polyisocyanurate (Pir) foams for thermal insulation
13204 : 1991 Specification for rigid phenolic foams for thermal insulation
13286 : 1992 Methods of test for surface spread of flame for thermal insulation materials
THREADED FASTENERS AND RIVETS
207 : 1964 Specification for gate and shutter hooks and eyes (revised)
451 : 1999 Specification for technical supply conditions for wood screws (third revision)
554 : 1999 Specification for pipe threads where pressure-tide joints are made on the threads — Dimensions, tolerances and designation (fourth revision)
723 : 1972 Specification for steel countersunk head wire nails (second revision)
724 : 1964 Specification for mild steel and brass cup, ruler and square hooks and screw eyes (revised)
725 : 1961 Specification for copper wire nails (revised)
730 : 1978 Specification for hook bolts for corrugated sheet roofing (second revision)
1120 : 1975 Specification for coach screws (first revision)
1363 Specification for hexagon head bolts, screws and nuts of product grade C:
(Part 1) : 2002 Hexagon head bolts (size range M5 to M64) (fourth revision)
(Part 2) : 2002 Hexagon head screws (size range M5 to M64) (fourth revision)
(Part 3) : 2002 Part 3 Hexagon nuts (Size range M5 to M64) (fourth revision)
1364 Specification for hexagon head bolts, screws and nuts of product Grades A and B:
(Part 1) : 2002 Hexagon head bolts (size range M1.6 to M64) (fourth revision)
(Part 2) : 2002 Hexagon head screws (size range M1.6 to M64) (fourth revision)
IS No. Title
(Part 3) : 2002 Hexagon nuts (size range M1.6 to M64) (fourth revision)
(Part 4) : 2003 Hexagon thin nuts (chamfered) (size range M1.6 to M64) (fourth revision)
(Part 5) : 2002 Hexagon thin nuts (unchamfered) (size range M1.6 to M10) (fourth revision)
(Part 6) : 2002 Hexagon nuts, style 2
1365 : 1978 Specification for slotted countersunk head screws (third revision)
1366 : 2002 Specification for slotted cheese head screws (third revision)
1367 Specification for technical supply conditions for threaded steel fasteners:
(Part 1) : 2002 Introduction and general information (third revision)
(Part 2) : 2002 Product grades and tolerances (third revision)
(Part 3) : 2002 Mechanical properties and test methods for bolts, screws and studs with full loadability (fourth revision)
(Part 5) : 2002 Mechanical properties and test methods for set screws and similar threaded fasteners not under tensile stresses (third revision)
(Part 6) : 1994 Mechanical properties and test methods for nuts with specified proof loads (third revision)
(Part 7) : 1980 Mechanical properties and test methods for nuts without specified proof loads (second revision)
(Part 8) : 2002 Mechanical and performance properties for prevailing torque type steel hexagon nuts (third revision)
(Part 9/Sec 1) : Surface discontinuities, Section 1 1993 Bolts, screws and studs for general applications (third revision)
(Part 9/Sec 2) : Surface discontinuities, Section 2 1993 Bolts, screws and studs for special applications (third revision)
(Part 10) : 2002 Surface discontinuities on nuts (third revision)
General requirements for plain washers and lock washers (first revision)
(Part 14/Sec 3): 2002
Mechanical properties of corrosion resistance stainless steel fasteners, Section 3 Set screws and similar fasteners not under tensile stress (third revision)
5372: 1975
Specification for taper washer for channels (ISMC) (first revision)
5373: 1969
Specification for square washers for wood fastenings
5374: 1975
Specification for taper washers for L-beam (ISMB) (first revision)
(Part 16): 2002
Designation system and symbols (third revision)
5624: 1993
Specification for foundation bolts (first revision)
1929: 1982
Specification for hot forged steel rivets for hot closing (12 to 36 mm diameter) (first revision)
6113: 1970
Specification for aluminium fasteners for building purposes
2016: 1967
Specification for plain washers (first revision)
6610: 1972
Specification for heavy washers for steel structures
2155: 1982
Specification for cold forged solid steel rivets for hot closing (6 to 16 mm diameter) (first revision)
6623: 1985
Specification for high strength structural nuts (first revision)
2585: 1968
Specification for black square bolts and nuts (dia range 6 to 39 mm) and black square screws (dia range 6 to 24 mm) (first revision)
6639: 1972
Specification for hexagon bolts for steel structures
2643: 1999
Dimensions, tolerances and designation for pipe threads where pressure-tight joints are not made on the threads (second revision)
6649: 1985
Specification for hardened and tempered washers for high strength structural bolts and nuts (first revision)
2687: 1991
Specification for cap nuts (second revision)
6733: 1972
Specification for wall and roofing nails
2907: 1998
Specification for non-ferrous rivets (first revision)
6736: 1972
Specification for slotted raised countersunk head wood screws
2998: 1982
Specification for cold forged steel rivets for cold closing (1 to 16 mm diameter) (first revision)
6739: 1972
Specification for slotted round head wood screws
3063: 1994
Specification for fasteners single coil rectangular section spring lock washers (second revision)
6760: 1972
Specification for slotted countersunk head wood screws
3121: 1981
Specification for rigging screws and stretching screws (first revision)
8033: 1976
Specification for washers with square hole for wood fastenings
3468: 1991
Specification for pipe nuts (second revision)
8412: 1977
Specification for slotted countersunk head bolts for steel structures
3757: 1985
Specification for high strength structural bolts (second revision)
8822: 1978
Specification for slotted mushroom head roofing bolts
IS No. Title
10238 : 2001 Specification for step bolts for steel structures
12427 : 2001 Specification for transmission tower bolts