b) The list at the end of this part has been completely reclassified to make it more user friendly and updated to reflect the latest available Indian Standard and methods of test.
A reference to SP 21 ‘Summaries of Indian Standards for building materials’ may be useful. This publication gives the summaries of Indian Standards covering various building materials, fittings and components except standards relating to paints.
All standards cross-referred to in the main text of this Part, are subject to revision. The parties to agreement based on this section are encouraged to investigate the possibility of applying the most recent editions of the standards.
1Scope
This Part of the Code covers the requirements of building materials and components, and criteria for accepting new or alternative building materials and components.
2Materials
Every material used in fulfilment of the requirements of this Part, unless otherwise specified in the Code or approved, shall conform to the relevant Indian Standards. A list of Indian Standards as the ‘accepted standards’ is given at the end of this Part of the Code. At the time of publication of the Code, the editions indicated were valid. All standards are subject to amendments and revisions. The Authority shall take cognizance of such amendments and revisions. The latest version of a standard shall, as far as possible, be adopted at the time of enforcement of this Part of the Code.
2062 : 1999 Specification for steel for general structural purposes (fifth revision)
2830 : 1992 Specification for carbon steel billets ingots, blooms and slabs for re-rolling into steel for general structural purposes (second revision)
2831 : 2000 Specification for carbon steel billets ingots, blooms and slabs for re-rolling into low tensile structural steel (third revision)
8053 : 1976 Specification for steel ingots and billets for the production of steel wire for the manufacture of wood screws
IS No. Title
8500 : 1991 Specification for structural steels microalloyed (medium and high strength qualities)
8952 : 1995 Steel ingots, blooms and billets for production of mild steel wire rods for general engineering purposes (first revision)
9467 : 1980 Steel ingots and billets for production of rivet bars for structural purposes
c) Sheet and Strip
277 : 2003 Specification for galvanized steel sheets (plain and corrugated) (sixth revision)
412 : 1975 Specification for expanded metal steel sheets for general purposes (second revision)
513 : 1994 Specification for cold rolled low carbon steel sheets and strips (fourth revision)
1079 : 1994 Specification for hot rolled carbon steel sheet and strip (fifth revision)
(Part 5/Sec 2) : Andhra Pradesh, Section 2 1997 Engineering properties of building stones
(Part 5/Sec 3) : Andhra Pradesh, Section 3 1997 Engineering properties of stone aggregates 9394 : 1979 Specification for stone lintels
14223 (Part 1) : Specification for polished building 1994 stones: Part 1 Granite
List of Standards
Following are the Indian Standards for various building materials and components, to be complied with in fulfillment of the requirements of the Code.
In the following list, while enlisting the Indian Standards, the materials have been categorized in such a way as to make the list user friendly. In the process, if so required, some of the standards have been included even in more than one category of products, such as in the category based on composition as well as on end application of the materials. The list has been arranged in alphabetical order of their principal category as given below:
IS No.
Title
733 : 1983
Specification for wrought aluminium and aluminium alloys, bars, rods and sections for general engineering purposes (third revision)
737 : 1986
Specification for wrought aluminium and aluminium alloys, sheet rods and strip for general engineering purposes (third revision)
1. ALUMINIUM AND OTHER LIGHT METALS AND THEIR ALLOYS
2. BITUMEN AND TAR PRODUCTS
3. BUILDER'S HARDWARES
738 : 1994
Specification for wrought aluminium and aluminium alloy drawn tube for general engineering purposes (third revision)
4. BUILDING CHEMICALS
5. BUILDING LIME AND PRODUCTS
6. BURNT CLAY PRODUCTS
7. CEMENT AND CONCRETE (including concrete reinforcement)
740 : 1977
Specification for wrought aluminium and aluminium alloy rivet stock for general engineering purposes (second revision)
Specification for corrugated aluminium sheet (third revision)
10. DOORS, WINDOWS AND VENTILATORS
11. ELECTRICAL WIRING, FITTINGS AND ACCESSORIES
1284 : 1975
Wrought aluminium alloy bolt and screw stock for general engineering purposes (second revision)
12. FILLERS, STOPPERS AND PUTTIES
13. FLOOR COVERING, ROOFING AND OTHER FINISHES
1285 : 2002
Specification for wrought aluminium and aluminium alloys, extruded round tube and hollow sections for general engineering purposes (third revision)
14. GLASS
15. GYPSUM BASED MATERIALS
16. LIGNOCELLULOSIC BUILDING MATERIALS (including timber, bamboo and products thereof)
2479 : 1981
Colour code for the identification of aluminium and aluminium alloys for general engineering purposes (second revision)
17. PAINTS AND ALLIED PRODUCTS
18. POLYMERS, PLASTICS AND GEOSYNTHETICS/GEOTEXTILES
2676 : 1981
Dimensions for wrought aluminium and aluminium alloy sheet and strip
19. SANITARY APPLIANCES AND WATER FITTINGS
20. SOIL-BASED PRODUCTS
2677 : 1979
Dimensions for wrought aluminium and aluminium alloys, plates and hot rolled sheets
21. STEEL AND ITS ALLOYS
22. STONES
23. STRUCTURAL SECTIONS
14712 : 1999
Wrought aluminium and its alloys — Chequered/tread sheets for general engineering purposes — Specification
24. THERMAL INSULATION MATERIALS
25. THREADED FASTENERS AND RIVETS
26. UNIT WEIGHTS OF BUILDING MATERIALS
27. WATERPROOFING AND DAMP-PROOFING MATERIALS
2. BITUMEN AND TAR PRODUCTS
73 : 1992
Specification for paving bitumen (second revision)
28. WELDING ELECTRODES AND WIRES
17Paints and Allied Products
a) Water Based Paints and Pigments
427 : 1965 Specification for distemper, dry, colour as required (revised)
428 : 2000 Specification for distemper, washable (second revision)
5410 : 1992 Specification for cement paint, colour as required (first revision)
5411 Specification for plastic emulsion paint:
(Part 1) : 1974 For interior use (first revision)
(Part 2) : 1972 For exterior use
b) Ready Mixed Paints, Enamels and Powder Coatings
101 Methods of sampling and test for paints, varnishes and related products:
(Part 1/Sec 1) : Test on liquid paints (general 1986 and physical), Section 1 Sampling (third revision)
(Part 1/Sec 2) : Test on liquid paints (general 1987 and physical), Section 2 Preliminary examination and preparation of samples for testing (third revision)
(Part 1/Sec 3) : Test on liquid paints (general and 1986 physical), Section 3 Preparation of panels (third revision)
(Part 1/Sec 4) : Test on liquid paints (general and 1987 physical), Section 4 Brushing test (third revision)
(Part 1/Sec 5) : Test on liquid paints (general and 1989 physical), Section 5 Consistency (third revision)
(Part 1/Sec 6) : Test on liquid paints (general and 1987 physical), Section 6 Flash point (third revision)
IS No. Title
(Part 1/Sec 7) : Test on liquid paints (general and 1987 physical), Section 7 Mass per 10 litres (third revision)
(Part 2/Sec 1) : Test on liquid paints (chemical 1988 examination), Section 1 Water content (third revision)
(Part 2/Sec 2) : Test on liquid paints (chemical 1986 examination), Section 2 Volatile matter (third revision)
(Part 3/Sec 1) : Tests on paint film formation, 1986 Section 1 Drying time (third revision)
(Part 3/Sec 2) : Tests on paint film formation, 1989 Section 2 Film thickness (third revision)
(Part 3/Sec 4) : Tests on paint film formation, 1987 Section 4 Finish (third revision)
(Part 3/Sec 5) : Tests on paint film formation, 1987 Section 5 Fineness of grind (third revision)
Specification for vitreous enamelled steel kitchen sinks
14643 : 1999
Specification for unsintered polytetrafluoroethylene (PTFE) tape for thread sealing applications
8727 : 1978
Specification for vitreous enamelled steel wash basins
14706 : 1999
Sampling and preparation of test specimen of geotextiles
9140 : 1996
Method of sampling of vitreous and fire clay sanitary appliances (second revision)
14714 : 1999
Determination of abrasion resistance of geotextiles
12701 : 1996
Specification for rotational moulded polyethylene water storage tanks (first revision)
14715 : 2000
Specification for woven jute geotextiles
13983 : 1994
Specification for stainless steel sinks for domestic purposes
14716 : 1999
Determination of mass per unit area of geotextiles
14399
Hot press moulded thermosetting glass fibre reinforced (GRP) sectional water storage tanks:
14739 : 1999
Methods for determination of creep of geotextiles
(Part 1) : 1996
Specification for panels
14753 : 1999
Specification for poly (methyl) methacrylate (PMMA) (Acrylic) sheets
(Part 2) : 1996
Guidelines for assembly, installation and testing
14986 : 2001
Jute geo-grid for rain water erosion control in road and railway embankments and hill slopes
b) Pipes and Fittings Excluding Valves
b) Pipes and Fittings Excluding Valves
14986 : 2001
Jute geo-grid for rain water erosion control in road and railway embankments and hill slopes
i) Brass and Copper Pipes and Fittings
i) Brass and Copper Pipes and Fittings
IS No.
Title
IS No.
Title
(Part 2): 2003
Specific requirements for 90° bends (first revision)
12235
Methods of test for unplasticized PVC pipes for potable water supplies:
(Part 3): 2003
Specific requirements for 90° tees
(Part 4): 2003
Specific requirements for reducers
(Part 1): 1986
Method of measurement of outside diameter
(Part 5): 2003
Specific requirements for ferrule reducers (first revision)
(Part 2): 1986
Measurement of wall thickness
(Part 6): 2003
Specific requirements for pipe ends
(Part 3): 1986
Test for opacity
(Part 7): 2003
Specific requirements for sandwich flanges
(Part 4): 1986
Determining the detrimental effect on the composition of water
(Part 8): 2003
Specific requirements for reducing tests
(Part 5): 1986
Reversion test
(Part 9): 2003
Specific requirements for end caps (first revision)
(Part 6): 1986
Stress relief test
8360
Specification for fabricated high density polyethelene (HDPE) fittings for potable water supplies:
(Part 7): 1986
Test for resistance to sulphuric acid
(Part 8): 1986
Internal hydrostatic pressure test
(Part 9): 1986
Impact strength test
(Part 10): 1986
Method for determination of organotin as tin aqueous solution
(Part 1): 1977
General requirements
(Part 11): 1986
Extractability of cadmium and mercury occurring as impurities
(Part 2): 1977
Specific requirements for 90° tees
(Part 3): 1977
Specific requirements for 90° bends
12709: 1994
Specification for glass-fibre reinforced plastic (GRP) pipes joints and fittings for use for potable water supply (first revision)
10124
Specification for fabricated PVC fittings for potable water supplies:
(Part 1): 1988
General requirements (first revision)
12818: 1992
Specification for unplasticized PVC screen and casing pipes for bore/tubewell (first revision)
(Part 2): 1988
Specific requirements for sockets (first revision)
IS No. Title
vi) Steel Tubes, Pipes and Fittings 1239 Mild steel tubes, tubular and other wrought steel fittings: (Part 1) : 1990 Mild steel tubes (fifth revision)
(Part 2): 1992 Mild steel tubular and other wrought steel pipe fittings (third revision)
3589:1991 Specification for seamless or electrically welded steel pipes for water, gas and sewage (168.3 to 2 032 mm outside size) (second revision)
4270:1992 Steel tubes used for water wells (second revision)
5504:1997 Specification for spiral welded pipes (first revision)
6286:1979 Seamless and welded steel pipe for sub-zero temperature service
6392: 1971 Steel pipe flanges
vii) Stoneware Pipes and Fittings
651: 1992 Specification for salt-glazed stoneware pipes and fittings (fifth revision)
3006:1979 Specification for chemically resistant glazed stoneware pipes and fittings (first revision)
viii) Asbestos Cement Pipes [See 8 (a) (ii) under the category Composite Matrix Products']
ix) Concrete Pipes and Pipes Lined/Coated with Concrete or Mortar [See 8 (a) (iv) under the category 'Composite Matrix Products']
c) Kitchen and Sanitary Appliances
771 Specification for glazed fire clay sanitary appliances:
(Part 1) : 1979 General requirements (second revision)
(Part 2) : 1985 Specific requirements of kitchen and laboratory sinks (third revision)
(Part 3/Sec 1) : Specific requirements of urinals, 1979 Section 1 Slab urinals (second revision)
(Part 3/Sec 2) : Part 3Specific requirements of 1985 urinals, Section 2 Stall urinals (third revision)
IS No. Title
(Part 4) : 1979 Specific requirements of post mortom slabs (second revision)
(Part 5) : 1979 Specific requirements of shower trays (second revision)
(Part 6) : 1979 Specific requirements of bed-pan sinks (second revision)
(Part 7):1981 Specific requirements of slop sinks (second revision)
772:1973 Specification for general requirements of enamelled cast iron sanitary appliances (second revision)
773:1988 Specification for enamelled cast iron water-closets railway stock type (fourth revision)
774:1984 Specification for flushing cisterns for water-closets and urinals (other than plastic cisterns) (fourth revision)
1726:1991 Specification for cast iron manhole covers and frames (third revision)
2326:1987 Specification for automatic flushing cisterns for urinals (second revision)
2548 Specification for plastic seats and covers for water-closets:
(Part 1) : 1996 Thermoset seats and covers (fifth revision)
(Part 2) : 1996 Thermoplastic seats and covers (fifth revision) 2556 Specification for vitreous sanitary appliances (vitreous china):
(Part 1): 1994 General requirements (third revision)
(Part 2) : 1994 Specific requirements of washdown water-closets (fourth revision)
(Part 3) : 1994 Specific requirements of squatting pans (fourth revision)
(Part 4) : 1994 Specific requirementsof wash basins (third revision)
(Part 5) : 1994 Specific requirements of laboratory sinks (third revision)
(Part 6) : 1995 Specific requirements of urinals and partition plates (fourth revision)
(Part 7) : 1995 Specific requirements of accessories for sanitary appliances (third revision)
(Part 8) : 1995 Specific requirements of siphonic wash-down water closets (fourth revision)
IS No.
Title
IS No.
Title
(Part 9):1995
Specific requirements of bidets (fourth revision)
3950:1979
Specification for surface boxes for sluice valves (first revision)
(Part 14):1995
Specific requirements of integrated squatting pans (first revision)
20 Soil-based Products
1725 : 1982 Specification for soil-based blocks used in general building construction
29Wire Ropes and Wire Products
ALUMINIUM AND OTHER LIGHT METALS AND THEIR ALLOYS
IS No.
Title
IS No.
Title
212 : 1983
Specification for crude coal tar for general use (second revision)
1218 : 1978
Determination of phenols (first revision)
215 : 1995
Specification for road tar (third revision)
1219 : 1978
Determination of naphthalene (first revision)
216 : 1961
Specification for coal tar pitch (first revision)
1220 : 1978
Determination of volatile matter content (first revision)
217 : 1988
Specification for cutback bitumen (second revision)
3117 : 2004
Specification for bitumen emulsion for roads (anionic type) (first revision)
218 : 1983
Specification for creosote oil for use as wood preservatives (second revision)
8887 : 2004
Specification for bitumen emulsion for roads (cationic type) (second revision)
454 : 1994
Specification for cutback bitumen from waxy crude (second revision)
702 : 1988
Specification for industrial bitumen (second revision)
9381 : 1979
Methods for testing tar and bituminous materials: Determination of FRAASS breaking point of bitumen
1201 to 1220
Methods for testing tar and bituminous materials
1201 : 1978
Sampling (first revision)
9382 : 1979
Methods for testing tar and bituminous materials: Determination of effect of heat and air by thin film oven test
1202 : 1978
Determination of specific gravity (first revision)
1203 : 1978
Determination of penetration (first revision)
10511 : 1983
Method for determination of asphaltenes in bitumen by precipitation with normal haptane
1204 : 1978
Determination of residue of specified penetration (first revision)
1205 : 1978
5Building Lime and Products
712 : 1984 Specification for building limes (third revision)
1624 : 1986 Method of field testing of building lime (first revision)
2686 : 1977 Specification for cinder as fine aggregates for use in lime concrete (first revision)
3068 : 1986 Specification for broken brick (burnt-clay) coarse aggregates for use in lime concrete (second revision)
3115 : 1992 Specification for lime based blocks (second revision)
3182 : 1986 Specification for broken bricks (burnt clay) fine aggregates for use in lime mortar (second revision)
4098 : 1983 Specification for lime-pozzolana mixture (first revision)
4139 : 1989 Specification for calcium silicate bricks (second revision)
6932 Method of tests for building limes: (Part 1) : 1973 Determination of insoluble residue, loss on ignition, insoluble matter, silicon dioxide, ferric and aluminium oxide, calcium oxide and magnesium oxide
(Part 2) : 1973 Determination of carbon dioxide content
(Part 3) : 1973 Determination of residue on slaking of quicklime
(Part 4) : 1973 Determination of fineness of hydrated lime
(Part 5) : 1973 Determination of unhydrated oxide
IS No.
Title
IS No.
Title
(Part 6):1973
Determination of volume yield of quicklime
6165:1992
Dimensions for special shapes of clay bricks (first revision)
(Part 7):1973
Determination of compressive and transverse strength
11650:1991
Guide for manufacture of common burnt clay building bricks by semi-mechanized process (first revision)
(Part 8):1973
Determination of workability
(Part 9):1973
Determination of soundness
13757:1993
Specification for burnt clay fly ash building bricks
(Part 10):1973
Determination of popping and pitting of hydrated lime
d) Jallies
(Part 11):1984
Determination of setting time of hydrated lime
7556:1988
Specification for burnt clay jallies (first revision)
10360:1982
(Part 9):1986
Determination of compressive strength perpendicular to grain (second revision)
10420:1982
Method of determination of sound absorption coefficient of timber by standing wave method
(Part 10):1986
Determination of hardness under static indentation (second revision)
10754:1983
Method of determination of thermal conductivity of timber
(Part 11):1986
Determination of shear strength parallel to grain (second revision)
11215:1991
Methods for determination of moisture content of timber and timber products (first revision)
(Part 12):1986
Determination of tensile strength parallel to grain (second revision)
13621:1993
Method of test for determination of dielectric constant of wood under microwave frequencies
(Part 13):1986
Determination of tensile strength perpendicular to grain (second revision)
(Part 14):1986
Determination of cleavage strength parallel to grain (second revision)
iv) Structural Timber and Test
(Part 15):1986
Determination of nail and screw holding power (second revision)
3629:1986
Specification for structural timber in building (first revision)
(Part 16):1986
Determination of brittleness by ized impact (second revision)
4891:1988
Specification for preferred cut sizes of structural timber (first revision)
(Part 17):1986
Determination of brittleness by Charpy impact (second revision)
4924
Method of test for nail jointed timber trusses:
(Part 18):1986
Determination of torsional strength (second revision)
(Part 1):1968
Destructive test
(Part 2):1968
Proof test
1900:1974
Method of testing wood poles (first revision)
v) Logs
2408:1963
Methods of static tests of timbers in structural sizes
3364
Method of measurement and evaluation of defects in timber:
(Part 1):1976
Logs (first revision)
(Part 2):1976
Converted timber (first revision)
2455:1990
Method of sampling of model trees and logs for timber testing and their conversion (second revision)
4895:1985
Specification for teak logs (first revision)
5246:2000
Specification for coniferous logs (first revision)
2753
Methods for estimation of preservatives in treated timber and treating solutions:
7308:1999
Specification for non-coniferous logs (first revision)
IS No. Title
6874 : 1973 Method of tests for round bamboos
8242 : 1976 Methods of tests for split bamboos
(Part 5) : 1977 Determination of tensile strength perpendicular to surface (first revision)
(Part 6) : 1977 Determination of tensile strength parallel to surface (first revision)
(Part 7) : 1977 Determination of compression — Perpendicular to plane of the board (first revision)
(Part 8) : 1977 Compression parallel to surface test (first revision)
(Part 9) : 1977 Determination of resistance to shear in plane of the board (first revision)
(Part 10) : 1977 Falling hammer impact test (first revision)
(Part 1/Sec 2) : Gujarat state, Section 2 Engineering 1975 properties of building stones
(Part 8/Sec 6):1993
Tests for pigments and other solids, Section 6 Volume solids
(Part 9/Sec 1):1993
Tests for lacquers and varnish, Section 1 Acid value
3536:1999
Specification for ready mixed paint, brushing, wood primer (first revision)
(Part 9/Sec 2):1993
Tests for lacquers and varnish, Section 2 Rosin test
3537:1966
Specification for ready mixed paint, finishing, interior for general purposes, to Indian Standard colours No. 101, 216, 217, 219, 275, 281, 352, 353, 358 to 361, 363, 364, 388, 410, 442, 444, 628, 631, 632, 634, 693, 697, white and black
Specification for ready mixed paint, brushing, priming, plaster to Indian Standard colours No. 361 and 631 (first revision)
3539:1966
Specification for ready mixed paint, undercoating, for use under oil finishes, to Indian Standard colours, as required
123:1962
Specification for ready mixed paint, brushing, finishing, semi-gloss, for general purposes, to Indian Standard colours No. 445, 446, 448, 449, 451 and 473; and red oxide (colour unspecified) (revised)
3585:1966
Specification for ready mixed paint, aluminium, brushing, priming, water resistant, for wood work
3678 : 1966
Specification for ready mixed paint, thick white, for lettering
18. POLYMERS, PLASTICS AND GEOSYNTHETICS/GEOTEXTILES
18. POLYMERS, PLASTICS AND GEOSYNTHETICS/GEOTEXTILES
8662 : 1993
Specification for enamel, synthetic, exterior, (a) undercoating, (b) finishing, for railway coaches (first revision)
1998 : 1962
Methods of test for thermosetting synthetic resin bonded laminated sheets
9862 : 1981
Specification for ready mixed paint, brushing, bituminous black lead free, acid, alkali, water and chlorine resisting
2036 : 1995
Specification for phenolic laminated sheets (second revision)
9862 : 1981
Specification for ready mixed paint, brushing, bituminous black lead free, acid, alkali, water and chlorine resisting
Specification for ready mixed paint, brushing, red oxide, priming for metals
2076 : 1981
Specification for unsupported flexible vinyl film and sheeting (first revision)
13183 : 1991
Specification for aluminium paints, heat resistant
2508 : 1984
Specification for low density polyethylene films (second revision)
13213 : 1991
Specification for polyurethane full gloss enamel (two pack)
2508 : 1984
Specification for low density polyethylene films (second revision)
13607 : 1992
Specification for ready mixed paint, finishing, general purposes, synthetic
6307 : 1971
Specification for rigid PVC sheets
13607 : 1992
Specification for ready mixed paint, finishing, general purposes, synthetic
9766 : 1992
Specification for flexible PVC compound (first revision)
13871 : 1993
Specification for powder coatings
10889 : 1984
Specification for high density polyethylene films
c) Thinners and Solvents
c) Thinners and Solvents
c) Thinners and Solvents
c) Thinners and Solvents
82 : 1992
Methods of sampling and test for thinners and solvents for paints (first revision)
12830 : 1989
Specification for rubber based adhesives for fixing PVC tiles to cement
324 : 1959
Specification for ordinary denatured spirit (revised)
13162
Methods of test for geotextiles:
324 : 1959
Specification for ordinary denatured spirit (revised)
(Part 2) : 1991
Determination of resistance to exposure of ultra-violet light and water (Xenon arc type apparatus)
533 : 1998
Specification for gum spirit of turpentine (oil of turpentine) (second revision)
(Part 3) : 1992
Determination of thickness at specified pressure
14314 : 1995
Specification for thinner general purposes for synthetic paints and varnishes
(Part 4) : 1992
Determination of puncture resistance by falling cone method
14314 : 1995
Specification for thinner general purposes for synthetic paints and varnishes
(Part 5) : 1992
Determination of tensile properties using a wide width strip
d) Varnishes and Lacquers
d) Varnishes and Lacquers
d) Varnishes and Lacquers
d) Varnishes and Lacquers
337 : 1975
Specification for varnish, finishing, interior (first revision)
13262 : 1992
Specification for pressure sensitive adhesive tapes with plastic base
347 : 1975
Specification for varnish, shellac, for general purposes (first revision)
13325 : 1992
Method of test for the determination to tensile properties of extruded polymer geogrids using the wide strip
348 : 1968
Specification for French polish (first revision)
13326 (Part 1) : 1992
Method of test for the evaluation of interface friction between geosynthetics and soil: Part 1 Modified direct shear technique
524 : 1983
Specification for varnish, finishing, exterior, synthetic (second revision)
13326 (Part 1) : 1992
Method of test for the evaluation of interface friction between geosynthetics and soil: Part 1 Modified direct shear technique
525 : 1968
Specification for varnish, finishing, exterior and general purposes (first revision)
14182 : 1994
Specification for solvent cement for use with unplasticized polyvinylchloride plastic pipe and fittings
642 : 1963
Specification for varnish medium for aluminium paint (revised)
14182 : 1994
Specification for solvent cement for use with unplasticized polyvinylchloride plastic pipe and fittings
15060 : 2001
Tensile test for joints/seams by wide width method of geotextiles
407 : 1981
Specification for brass tubes for general purposes (third revision)
15060 : 2001
Tensile test for joints/seams by wide width method of geotextiles
2501 : 1995
Specification for solid drawn copper tubes for general engineering purposes (third revision)
19. SANITARY Fittings
APPLIANCES AND WATER
a) General
ii) Cast Iron Pipes and Fittings
ii) Cast Iron Pipes and Fittings
775 : 1970
Specification for cast iron brackets and supports for wash basins and sinks (second revision)
1536 : 2001
Specification for centrifugally cast (spun) iron pressure pipes for water, gas and sewage (fourth revision)
782 : 1978
Specification for caulking lead (third revision)
1537 : 1976
Specification for vertically cast iron pressure pipes for water, gas and sewage (first revision)
804 : 1967
Specification for rectangular pressed steel tanks (first revision)
1538 : 1993
Specification for cast iron fittings for pressure pipes for water, gas and sewage (third revision)
1700 : 1973
Specification for drinking fountains (first revision)
1729 : 2002
Specification for sand cast iron spigot and socket soil, waste and ventilating pipes, fittings and accessories (second revision)
2963 : 1979
Specification for copper alloy waste fittings for wash-basins and sinks (first revision)
3489 : 1985
Specification for enamelled steel bath tubs (first revision)
IS No.
Title
IS No.
Title
1879 : 1987
Specification for malleable cast iron pipe fittings (second revision)
12988 : 1991
Rubber sealing rings for CID joints for light duty AC pipes — Dimensional requirements
3486 : 1966
Specification for cast iron spigot and socket drain pipes
13382 : 1992
Cast iron specials for mechanical and push on flexible joints for pressure pipelines for water, gas and sewage
3989 : 1984
Specification for centrifugally cast (spun) iron spigot and socket soil, waste and ventilating pipes, fittings and accessories (second revision)
5531 : 1988
Specification for cast iron specials for asbestos cement pressure pipes for water, gas and sewage (second revision)
404 (Part 1) : 1993
Specification for lead pipes: Part 1 For other than chemical purpose (third revision)
6163 : 1978
Specification for centrifugally cast (spun) iron low pressure pipes for water, gas and sewage (first revision)
iv) Fibre Pipes and Fittings
iv) Fibre Pipes and Fittings
6163 : 1978
Specification for centrifugally cast (spun) iron low pressure pipes for water, gas and sewage (first revision)
11925 : 1986
Specification for pitch-impregnated fibre pipes and fittings for drainage purposes
6418 : 1971
Specification for cast iron and malleable cast iron flanges for general engineering purposes
v) Plastic Pipes and Fittings
v) Plastic Pipes and Fittings
6418 : 1971
Specification for cast iron and malleable cast iron flanges for general engineering purposes
3076 : 1985
Specification for low density polyethylene pipes for potable water supplies (second revision)
7181 : 1986
Specification for horizontally cast iron double flanged pipes for water, gas and sewage (first revision)
4984 : 1995
Specification for high density polyethylene pipes for water supply (fourth revision)
8329 : 2000
Specification for centrifugally cast (spun) ductile iron pressure pipes for water, gas and sewage (third revision)
4985 : 2000
Specification for unplasticized PVC pipes for potable water supplies (third revision)
8794 : 1988
Specification for cast iron detachable joints for use with asbestos cement pressure pipes (first revision)
7834
Specification for injection moulded PVC socket fittings with solvent cement joints for water supplies:
9523 : 1980
Specification for ductile iron fittings for pressure pipes for water, gas and sewage
(Part 1) : 1987
General requirements (first revision)
9523 : 1980
Specification for ductile iron fittings for pressure pipes for water, gas and sewage
(Part 2) : 1987
Specific requirements for 45° elbows (first revision)
10292 : 1988
Dimensional requirements for rubber sealing rings for CID joints in asbestos cement piping (first revision)
(Part 3) : 1987
Specific requirements for 90° elbows (first revision)
10292 : 1988
Dimensional requirements for rubber sealing rings for CID joints in asbestos cement piping (first revision)
(Part 4) : 1987
Specific requirements for 90° tees (first revision)
10299 : 1982
Cast iron saddle pieces for service connection from asbestos cement pressure pipes
(Part 5) : 1987
Specific requirements for 45° tees (first revision)
11606 : 1986
Methods of sampling cast iron pipes and fittings
(Part 6) : 1987
Specific requirements for sockets (first revision)
12820 : 1989
Dimensional requirements of rubber gaskets for mechanical joints and push on joints for use with cast iron pipes and fittings for carrying water, gas and sewage
(Part 7) : 1987
Specific requirements for unions (first revision)
12820 : 1989
Dimensional requirements of rubber gaskets for mechanical joints and push on joints for use with cast iron pipes and fittings for carrying water, gas and sewage
(Part 8) : 1987
Specific requirements for caps (first revision)
12987 : 1991
Cast iron detachable joints for use with asbestos cement pressure pipes (light duty)
8008
Specification for injection moulded high density polyethylene (HDPE) fittings for potable water supplies:
12987 : 1991
Cast iron detachable joints for use with asbestos cement pressure pipes (light duty)
(Part 1) : 2003
General requirements
(Part 3): 1988
Specific requirements of straight reducers (first revision)
13592: 1992
Specification for UPVC pipes for soil and waste discharge systems inside buildings including ventilation and rainwater system
(Part 4): 1988
Specific requirements for caps (first revision)
14333: 1996
Specification for high density polyethylene pipes for sewerage
(Part 5): 1988
Specific requirements for equal tees (first revision)
14402: 1996
Specification for GRP pipes, joints and fittings for use for sewerage, industrial waste and water (other than potable)
(Part 6): 1988
Specific requirements for flanged tail piece with metallic flanges (first revision)
(Part 7): 1988
Specific requirements for threaded adaptors (first revision)
14735: 1999
Specification for unplasticized polyvinyl chloride (UPVC) injection moulded fittings for soil and waste discharge system for inside buildings including ventilation and rain water system
(Part 8): 1988
Specific requirements for 90° bends (first revision)
(Part 9): 1988
Specific requirements for 60° bends (first revision)
14885: 2001
Specification for polyethylene pipe for supply of gaseous fuel
(Part 10): 1988
Specific requirements for 45° bends (first revision)
15225: 2002
Specification for chlorinated polyvinyl chloride compounds used for pipes and fittings
(Part 11): 1988
Specific requirements for 30° bends (first revision)
(Part 12): 1988
Specific requirements for 221⁄2° bends (first revision)
15328: 2003
Specification for unplasticized non-pressure polyvinyl chloride (PVC-U) pipes for use in underground drainage and sewerage system
(Part 13): 1988
Specific requirements for 111⁄4° bends (first revision)
4038:1986
Specification for foot valves for water works purposes (second revision)
(Part 15):1995
Specific requirements of universal water closets (first revision)
4346:1982
Specification for washers for use with fittings for water services (first revision)
(Part 16):2002
Specific requirements for wash down wall mounted water-closets
(Part 17):1995
Specific requirements for wall mounted bidets
5312
Specification for swing check type reflux (non-return) valves:
5961:1970
Specification for cast iron gratings for drainage purposes
(Part 1):1984
Single door pattern (first revision)
(Part 2):1986
Multi-door pattern
7231:1984
Specification for plastic flushing cisterns for water-closets and urinals (second revision)
8931:1993
Specification for cast copper alloy fancy single tap combination tap and stop valves for water services (first revision)
13008 : 1990 Specification for shallow corrugated asbestos cement sheets
iii) Other Fibre Cement Products
14862 : 2000 Specification for fibre cement flat sheets
14871 : 2000 Specification for products in fibre reinforced cement long corrugated or asymmetrical section sheets and fittings for roofing and cladding
iv) Concrete Pipes and Pipes Lined/Coated with Concrete or Mortar
458 : 2003 Specification for precast concrete pipes (with and without reinforcement) (fourth revision)
1003 Specification for timber panelled and glazed shutters:
(Part 1) : 2003 Door shutters (fourth revision)
(Part 2) : 1994 Window and ventilator shutters (third revision)
1826 : 1961 Specification for venetian blinds for windows
(Part 1) : 1983 Plywood face panels (fourth revision)
(Part 2) : 1983 Particle board face panels and hardboard face panels (third revision) 2202 Specification for wooden flush door shutters (solid core type):
(Part 1) : 1991 Plywood face panels (fifth revision)
(Part 2) : 1983 Particle board face panels and hardboard face panels (third revision)
4020 Method of tests for door shutters:
(Part 1) : 1998 General (third revision)
(Part 2) : 1998 Measurement of dimensions and squareness (third revision)
(Part 3) : 1998 Measurement of general flatness (third revision)
(Part 4) : 1998 Local planeness test (third revision)
(Part 5) : 1998 Impact indentation test (third revision)
IS No. Title
(Part 6) : 1998 Flexure test (third revision)
(Part 7) : 1998 Edge loading test (third revision)
(Part 8) : 1998 Shock resistance test (third revision)
(Part 9) : 1998 Buckling resistance test (third revision)
(Part 10) : 1998 Slamming test (third revision)
(Part 11) : 1998 Misuse test (third revision)
(Part 12) : 1998 Varying humidity test (third revision)
(Part 13) : 1998 End immersion test (third revision)
(Part 14) : 1998 Knife test (third revision)
(Part 15) : 1998 Glue adhesion test (third revision)
(Part 16) : 1998 Screw withdrawal resistance test (third revision)
4021 : 1995 Specification for timber door, window and ventilator frames
4962 : 1968 Specification for wooden side sliding doors
6198 : 1992 Specification for ledged, braced and battened timber shutters (second revision)
b) Metal Doors, Windows Frames and Ventilators
1038 : 1983 Specification for steel doors, windows and ventilators (third revision)
1361 : 1978 Specification for steel windows for industrial buildings (first revision)
1948 : 1961 Specification for aluminium doors, windows and ventilators
1949 : 1961 Specification for aluminium windows for industrial buildings
4351 : 2003 Specification for steel door frames (second revision)
6248 : 1979 Specification for metal rolling shutters and rolling grills (first revision)
7452 : 1990 Specification for hot rolled steel sections for doors, windows and ventilators (second revision)