b) The list at the end of this part has been completely reclassified to make it more user friendly and updated to reflect the latest available Indian Standard and methods of test.
A reference to SP 21 ‘Summaries of Indian Standards for building materials’ may be useful. This publication gives the summaries of Indian Standards covering various building materials, fittings and components except standards relating to paints.
All standards cross-referred to in the main text of this Part, are subject to revision. The parties to agreement based on this section are encouraged to investigate the possibility of applying the most recent editions of the standards.
2Materials
Every material used in fulfilment of the requirements of this Part, unless otherwise specified in the Code or approved, shall conform to the relevant Indian Standards. A list of Indian Standards as the ‘accepted standards’ is given at the end of this Part of the Code. At the time of publication of the Code, the editions indicated were valid. All standards are subject to amendments and revisions. The Authority shall take cognizance of such amendments and revisions. The latest version of a standard shall, as far as possible, be adopted at the time of enforcement of this Part of the Code.
1Scope
This Part of the Code covers the requirements of building materials and components, and criteria for accepting new or alternative building materials and components.
List of Standards
Following are the Indian Standards for various building materials and components, to be complied with in fulfillment of the requirements of the Code.
In the following list, while enlisting the Indian Standards, the materials have been categorized in such a way as to make the list user friendly. In the process, if so required, some of the standards have been included even in more than one category of products, such as in the category based on composition as well as on end application of the materials. The list has been arranged in alphabetical order of their principal category as given below:
IS No.
Title
733 : 1983
Specification for wrought aluminium and aluminium alloys, bars, rods and sections for general engineering purposes (third revision)
737 : 1986
Specification for wrought aluminium and aluminium alloys, sheet rods and strip for general engineering purposes (third revision)
1. ALUMINIUM AND OTHER LIGHT METALS AND THEIR ALLOYS
2. BITUMEN AND TAR PRODUCTS
3. BUILDER'S HARDWARES
738 : 1994
Specification for wrought aluminium and aluminium alloy drawn tube for general engineering purposes (third revision)
4. BUILDING CHEMICALS
5. BUILDING LIME AND PRODUCTS
6. BURNT CLAY PRODUCTS
7. CEMENT AND CONCRETE (including concrete reinforcement)
740 : 1977
Specification for wrought aluminium and aluminium alloy rivet stock for general engineering purposes (second revision)
(Part 2) : 1984 CNSL aldehyde resin and coconut pith 11433 Specification for one grade
(Part 1) : 1985 polysulphide based joint sealant: Part 1 General requirements
12118 Specification for two parts polysulphide based sealants:
(Part 2) : 1987 Methods of test
d) Adhesives
848 : 1974 Specification for synthetic resin adhesives for plywood (phenolic and aminoplastic) (first revision)
849 : 1994 Specification for cold setting case in glue for wood (first revision)
851 : 1978 Specification for synthetic resin adhesives for construction work (non-structural) in wood (first revision)
852 : 1994 Specification for animal glue for general wood-working purposes (second revision)
4835 : 1979 Specification for polyvinyl acetate dispersion-based adhesives for wood (first revision)
9188 : 1979 Performance requirements for adhesive for structural laminated wood products for use under exterior exposure condition
12830 : 1989 Rubber based adhesives for fixing PVC tiles to cement
12994 : 1990 Epoxy adhesives, room temperature curing general purpose
17Paints and Allied Products
a) Water Based Paints and Pigments
427 : 1965 Specification for distemper, dry, colour as required (revised)
428 : 2000 Specification for distemper, washable (second revision)
5410 : 1992 Specification for cement paint, colour as required (first revision)
5411 Specification for plastic emulsion paint:
(Part 1) : 1974 For interior use (first revision)
(Part 2) : 1972 For exterior use
b) Ready Mixed Paints, Enamels and Powder Coatings
101 Methods of sampling and test for paints, varnishes and related products:
(Part 1/Sec 1) : Test on liquid paints (general 1986 and physical), Section 1 Sampling (third revision)
(Part 1/Sec 2) : Test on liquid paints (general 1987 and physical), Section 2 Preliminary examination and preparation of samples for testing (third revision)
(Part 1/Sec 3) : Test on liquid paints (general and 1986 physical), Section 3 Preparation of panels (third revision)
(Part 1/Sec 4) : Test on liquid paints (general and 1987 physical), Section 4 Brushing test (third revision)
(Part 1/Sec 5) : Test on liquid paints (general and 1989 physical), Section 5 Consistency (third revision)
(Part 1/Sec 6) : Test on liquid paints (general and 1987 physical), Section 6 Flash point (third revision)
IS No. Title
(Part 1/Sec 7) : Test on liquid paints (general and 1987 physical), Section 7 Mass per 10 litres (third revision)
(Part 2/Sec 1) : Test on liquid paints (chemical 1988 examination), Section 1 Water content (third revision)
(Part 2/Sec 2) : Test on liquid paints (chemical 1986 examination), Section 2 Volatile matter (third revision)
(Part 3/Sec 1) : Tests on paint film formation, 1986 Section 1 Drying time (third revision)
(Part 3/Sec 2) : Tests on paint film formation, 1989 Section 2 Film thickness (third revision)
(Part 3/Sec 4) : Tests on paint film formation, 1987 Section 4 Finish (third revision)
(Part 3/Sec 5) : Tests on paint film formation, 1987 Section 5 Fineness of grind (third revision)
Specification for vitreous enamelled steel kitchen sinks
14643 : 1999
Specification for unsintered polytetrafluoroethylene (PTFE) tape for thread sealing applications
8727 : 1978
Specification for vitreous enamelled steel wash basins
14706 : 1999
Sampling and preparation of test specimen of geotextiles
9140 : 1996
Method of sampling of vitreous and fire clay sanitary appliances (second revision)
14714 : 1999
Determination of abrasion resistance of geotextiles
12701 : 1996
Specification for rotational moulded polyethylene water storage tanks (first revision)
14715 : 2000
Specification for woven jute geotextiles
13983 : 1994
Specification for stainless steel sinks for domestic purposes
14716 : 1999
Determination of mass per unit area of geotextiles
14399
Hot press moulded thermosetting glass fibre reinforced (GRP) sectional water storage tanks:
14739 : 1999
Methods for determination of creep of geotextiles
(Part 1) : 1996
Specification for panels
14753 : 1999
Specification for poly (methyl) methacrylate (PMMA) (Acrylic) sheets
(Part 2) : 1996
Guidelines for assembly, installation and testing
14986 : 2001
Jute geo-grid for rain water erosion control in road and railway embankments and hill slopes
b) Pipes and Fittings Excluding Valves
b) Pipes and Fittings Excluding Valves
14986 : 2001
Jute geo-grid for rain water erosion control in road and railway embankments and hill slopes
i) Brass and Copper Pipes and Fittings
i) Brass and Copper Pipes and Fittings
IS No.
Title
IS No.
Title
(Part 2): 2003
Specific requirements for 90° bends (first revision)
12235
Methods of test for unplasticized PVC pipes for potable water supplies:
(Part 3): 2003
Specific requirements for 90° tees
(Part 4): 2003
Specific requirements for reducers
(Part 1): 1986
Method of measurement of outside diameter
(Part 5): 2003
Specific requirements for ferrule reducers (first revision)
(Part 2): 1986
Measurement of wall thickness
(Part 6): 2003
Specific requirements for pipe ends
(Part 3): 1986
Test for opacity
(Part 7): 2003
Specific requirements for sandwich flanges
(Part 4): 1986
Determining the detrimental effect on the composition of water
(Part 8): 2003
Specific requirements for reducing tests
(Part 5): 1986
Reversion test
(Part 9): 2003
Specific requirements for end caps (first revision)
(Part 6): 1986
Stress relief test
8360
Specification for fabricated high density polyethelene (HDPE) fittings for potable water supplies:
(Part 7): 1986
Test for resistance to sulphuric acid
(Part 8): 1986
Internal hydrostatic pressure test
(Part 9): 1986
Impact strength test
(Part 10): 1986
Method for determination of organotin as tin aqueous solution
(Part 1): 1977
General requirements
(Part 11): 1986
Extractability of cadmium and mercury occurring as impurities
(Part 2): 1977
Specific requirements for 90° tees
(Part 3): 1977
Specific requirements for 90° bends
12709: 1994
Specification for glass-fibre reinforced plastic (GRP) pipes joints and fittings for use for potable water supply (first revision)
10124
Specification for fabricated PVC fittings for potable water supplies:
(Part 1): 1988
General requirements (first revision)
12818: 1992
Specification for unplasticized PVC screen and casing pipes for bore/tubewell (first revision)
(Part 2): 1988
Specific requirements for sockets (first revision)
IS No. Title
vi) Steel Tubes, Pipes and Fittings 1239 Mild steel tubes, tubular and other wrought steel fittings: (Part 1) : 1990 Mild steel tubes (fifth revision)
(Part 2): 1992 Mild steel tubular and other wrought steel pipe fittings (third revision)
3589:1991 Specification for seamless or electrically welded steel pipes for water, gas and sewage (168.3 to 2 032 mm outside size) (second revision)
4270:1992 Steel tubes used for water wells (second revision)
5504:1997 Specification for spiral welded pipes (first revision)
6286:1979 Seamless and welded steel pipe for sub-zero temperature service
6392: 1971 Steel pipe flanges
vii) Stoneware Pipes and Fittings
651: 1992 Specification for salt-glazed stoneware pipes and fittings (fifth revision)
3006:1979 Specification for chemically resistant glazed stoneware pipes and fittings (first revision)
viii) Asbestos Cement Pipes [See 8 (a) (ii) under the category Composite Matrix Products']
ix) Concrete Pipes and Pipes Lined/Coated with Concrete or Mortar [See 8 (a) (iv) under the category 'Composite Matrix Products']
c) Kitchen and Sanitary Appliances
771 Specification for glazed fire clay sanitary appliances:
(Part 1) : 1979 General requirements (second revision)
(Part 2) : 1985 Specific requirements of kitchen and laboratory sinks (third revision)
(Part 3/Sec 1) : Specific requirements of urinals, 1979 Section 1 Slab urinals (second revision)
(Part 3/Sec 2) : Part 3Specific requirements of 1985 urinals, Section 2 Stall urinals (third revision)
IS No. Title
(Part 4) : 1979 Specific requirements of post mortom slabs (second revision)
(Part 5) : 1979 Specific requirements of shower trays (second revision)
(Part 6) : 1979 Specific requirements of bed-pan sinks (second revision)
(Part 7):1981 Specific requirements of slop sinks (second revision)
772:1973 Specification for general requirements of enamelled cast iron sanitary appliances (second revision)
773:1988 Specification for enamelled cast iron water-closets railway stock type (fourth revision)
774:1984 Specification for flushing cisterns for water-closets and urinals (other than plastic cisterns) (fourth revision)
1726:1991 Specification for cast iron manhole covers and frames (third revision)
2326:1987 Specification for automatic flushing cisterns for urinals (second revision)
2548 Specification for plastic seats and covers for water-closets:
(Part 1) : 1996 Thermoset seats and covers (fifth revision)
(Part 2) : 1996 Thermoplastic seats and covers (fifth revision) 2556 Specification for vitreous sanitary appliances (vitreous china):
(Part 1): 1994 General requirements (third revision)
(Part 2) : 1994 Specific requirements of washdown water-closets (fourth revision)
(Part 3) : 1994 Specific requirements of squatting pans (fourth revision)
(Part 4) : 1994 Specific requirementsof wash basins (third revision)
(Part 5) : 1994 Specific requirements of laboratory sinks (third revision)
(Part 6) : 1995 Specific requirements of urinals and partition plates (fourth revision)
(Part 7) : 1995 Specific requirements of accessories for sanitary appliances (third revision)
(Part 8) : 1995 Specific requirements of siphonic wash-down water closets (fourth revision)
IS No.
Title
IS No.
Title
(Part 9):1995
Specific requirements of bidets (fourth revision)
3950:1979
Specification for surface boxes for sluice valves (first revision)
(Part 14):1995
Specific requirements of integrated squatting pans (first revision)
20 Soil-based Products
1725 : 1982 Specification for soil-based blocks used in general building construction
10Doors, Windows and Ventilators
a) Wooden Doors, Windows and Ventilators
1003 Specification for timber panelled and glazed shutters:
(Part 1) : 2003 Door shutters (fourth revision)
(Part 2) : 1994 Window and ventilator shutters (third revision)
1826 : 1961 Specification for venetian blinds for windows
(Part 1) : 1983 Plywood face panels (fourth revision)
(Part 2) : 1983 Particle board face panels and hardboard face panels (third revision) 2202 Specification for wooden flush door shutters (solid core type):
(Part 1) : 1991 Plywood face panels (fifth revision)
(Part 2) : 1983 Particle board face panels and hardboard face panels (third revision)
4020 Method of tests for door shutters:
(Part 1) : 1998 General (third revision)
(Part 2) : 1998 Measurement of dimensions and squareness (third revision)
(Part 3) : 1998 Measurement of general flatness (third revision)
(Part 4) : 1998 Local planeness test (third revision)
(Part 5) : 1998 Impact indentation test (third revision)
IS No. Title
(Part 6) : 1998 Flexure test (third revision)
(Part 7) : 1998 Edge loading test (third revision)
(Part 8) : 1998 Shock resistance test (third revision)
(Part 9) : 1998 Buckling resistance test (third revision)
(Part 10) : 1998 Slamming test (third revision)
(Part 11) : 1998 Misuse test (third revision)
(Part 12) : 1998 Varying humidity test (third revision)
(Part 13) : 1998 End immersion test (third revision)
(Part 14) : 1998 Knife test (third revision)
(Part 15) : 1998 Glue adhesion test (third revision)
(Part 16) : 1998 Screw withdrawal resistance test (third revision)
4021 : 1995 Specification for timber door, window and ventilator frames
4962 : 1968 Specification for wooden side sliding doors
6198 : 1992 Specification for ledged, braced and battened timber shutters (second revision)
b) Metal Doors, Windows Frames and Ventilators
1038 : 1983 Specification for steel doors, windows and ventilators (third revision)
1361 : 1978 Specification for steel windows for industrial buildings (first revision)
1948 : 1961 Specification for aluminium doors, windows and ventilators
1949 : 1961 Specification for aluminium windows for industrial buildings
4351 : 2003 Specification for steel door frames (second revision)
6248 : 1979 Specification for metal rolling shutters and rolling grills (first revision)
7452 : 1990 Specification for hot rolled steel sections for doors, windows and ventilators (second revision)
3438 : 1994 Specification for silvered glass mirrors for general purposes (second revision)
5437 : 1994 Specification for figured rolled and wired glass (first revision)
14900 : 2000 Specification for transparent float glass
5Building Lime and Products
712 : 1984 Specification for building limes (third revision)
1624 : 1986 Method of field testing of building lime (first revision)
2686 : 1977 Specification for cinder as fine aggregates for use in lime concrete (first revision)
3068 : 1986 Specification for broken brick (burnt-clay) coarse aggregates for use in lime concrete (second revision)
3115 : 1992 Specification for lime based blocks (second revision)
3182 : 1986 Specification for broken bricks (burnt clay) fine aggregates for use in lime mortar (second revision)
4098 : 1983 Specification for lime-pozzolana mixture (first revision)
4139 : 1989 Specification for calcium silicate bricks (second revision)
6932 Method of tests for building limes: (Part 1) : 1973 Determination of insoluble residue, loss on ignition, insoluble matter, silicon dioxide, ferric and aluminium oxide, calcium oxide and magnesium oxide
(Part 2) : 1973 Determination of carbon dioxide content
(Part 3) : 1973 Determination of residue on slaking of quicklime
(Part 4) : 1973 Determination of fineness of hydrated lime
(Part 5) : 1973 Determination of unhydrated oxide
IS No.
Title
IS No.
Title
(Part 6):1973
Determination of volume yield of quicklime
6165:1992
Dimensions for special shapes of clay bricks (first revision)
(Part 7):1973
Determination of compressive and transverse strength
11650:1991
Guide for manufacture of common burnt clay building bricks by semi-mechanized process (first revision)
(Part 8):1973
Determination of workability
(Part 9):1973
Determination of soundness
13757:1993
Specification for burnt clay fly ash building bricks
(Part 10):1973
Determination of popping and pitting of hydrated lime
d) Jallies
(Part 11):1984
Determination of setting time of hydrated lime
7556:1988
Specification for burnt clay jallies (first revision)
10360:1982
Specification for lime pozzolana concrete blocks for paving
e) Tiles
10772:1983
Specification for quick setting lime pozzolana mixture
654:1992
Specification for clay roofing tiles, Mangalore pattern (third revision)
12894:2002
Specification for pulverized fuel ash lime bricks (first revision)
1464:1992
Specification for clay ridge and ceiling tiles (second revision)
6. BURNT CLAY PRODUCTS
6. BURNT CLAY PRODUCTS
1478:1992
Specification for clay flooring tiles (second revision)
a) Blocks
2690
Specification for burnt clay flat terracing tiles:
3952:1988
Specification for burnt hollow bricks for walls and partitions (second revision)
(Part 1):1993
Machine made (second revision)
3952:1988
Specification for burnt hollow bricks for walls and partitions (second revision)
(Part 2):1992
Handmade (second revision)
b) Soil-Based Products
b) Soil-Based Products
3367:1993
Specification for burnt clay tiles for use in lining irrigation and drainage works (second revision)
1725:1982
Specification for soil-based blocks used in general building construction
3951
Specification for hollow clay tiles for floor and roofs:
c) Bricks
1077:1992
Specification for common burnt clay building bricks (fifth revision)
(Part 1):1975
Filler type (first revision)
1077:1992
Specification for common burnt clay building bricks (fifth revision)
(Part 2):1975
Structural type (first revision)
2117:1991
Guide for manufacture of hand-made-common burnt clay building bricks (third revision)
13317:1992
Specification for clay roofing camty tiles, half round and flat tiles
2180:1988
Specification for heavy duty burnt clay building bricks (third revision)
7. CEMENT AND CONCRETE (including concrete reinforcement)
7. CEMENT AND CONCRETE (including concrete reinforcement)
2222:1991
Specification for burnt clay perforated building bricks (fourth revision)
a) Aggregates
2691:1988
Specification for burnt clay facing bricks (second revision)
383:1970
Specification for coarse and fine aggregates from natural sources for concrete (second revision)
3495(Parts 1 to 4):1992
Methods of test of burnt clay building bricks (third revision)
1542:1992
Specification for sand for plaster (second revision)
3583:1988
Specification for burnt clay paving bricks (second revision)
2116:1980
Specification for sand for masonry mortars (first revision)
4885:1988
Specification for sewer bricks (first revision)
2386
Methods of test for aggregates for concrete:
5454:1978
Methods for sampling of clay building bricks
(Part 1):1963
Particle size and shape
5779:1986
Specification for burnt clay soling bricks (first revision)
(Part 2):1963
Estimation of deleterious materials and organic impurities
(Part 3):1963
Specific gravity, density, voids, absorption and bulking
IS No.
Title
IS No.
Title
(Part 4):1963
Mechanical properties
3812
Specification for pulverized fuel ash:
(Part 5):1963
Soundness
Specification for pulverized fuel ash:
(Part 6):1963
Measuring mortar making properties of fine aggregates
(Part 1):2003
For use as pozzolana in cement, cement mortar and concrete (second revision)
(Part 7):1963
Alkali aggregate reactivity
For use as pozzolana in cement, cement mortar and concrete (second revision)
(Part 8):1963
Petrographic examination
(Part 2):2003
For use as admixture in cement mortar and concrete (second revision)
2430:1986
Methods of sampling of aggregates of concrete (first revision)
For use as admixture in cement mortar and concrete (second revision)
6579:1981
Specification for coarse aggregate for water bound macadam (first revision)
6491:1972
Method of sampling of flyash
6579:1981
Specification for coarse aggregate for water bound macadam (first revision)
6925:1973
Methods of test for determination of water soluble chlorides in concrete admixtures
9142:1979
Specification for artificial lightweight aggregates for concrete masonry units
9103:1999
Specification for admixtures for concrete (first revision)
b) Cement
12089:1987
Specification for granulated slag for manufacture of Portland slag cement
269:1989
Specification for ordinary portland cement, 33 Grade (fourth revision)
Specification for granulated slag for manufacture of Portland slag cement
455:1989
Specification for Portland slag cement (fourth revision)
12870:1989
Methods of sampling calcined clay pozzolana
1489
Specification for Portland pozzolana cement:
15388:2003
Specification for silica fume
1489
Specification for Portland pozzolana cement:
d) Concrete
(Part 1):1991
Flyash based (third revision)
456:2000
Code of practice for plain and reinforced concrete (fourth revision)
(Part 2):1991
Calcined clay based (third revision)
Code of practice for plain and reinforced concrete (fourth revision)
3466:1988
Specification for masonry cement (second revision)
1343:1980
Code of practice for prestressed concrete (first revision)
6452:1989
Specification for high alumina cement for structural use (first revision)
4926:2003
Code of practice for ready-mixed concrete (third revision)
6909:1990
Specification for supersulphated cement
e) Cement and Concrete Sampling and Methods of Test
8041:1990
Specification for rapid hardening Portland cement (second revision)
516:1959
Methods of test for strength of concrete
8042:1989
Specification for white Portland cement (second revision)
1199:1959
Methods of sampling and analysis of concrete
8043:1991
Specification for hydrophobic Portland cement (second revision)
2770
Methods of testing bond in reinforced concrete: Part 1 Pullout test
8112:1989
Specification for 43 grade ordinary Portland cement (first revision)
(Part 1):1967
Methods of testing bond in reinforced concrete: Part 1 Pullout test
12269:1987
Specification for 53 grade ordinary Portland cement
3085:1965
Methods of test for permeability of cement mortar and concrete
12330:1988
Specification for sulphate resisting Portland cement
3535:1986
Methods of sampling hydraulic cement (first revision)
12600:1989
Specification for low heat Portland cement
4031
Methods of physical tests for hydraulic cement:
c) Mineral/Chemical Admixtures and Pozzolanas
c) Mineral/Chemical Admixtures and Pozzolanas
(Part 1):1996
Determination of fineness by dry sieving (second revision)
1344:1981
Specification for calcined clay pozzolana (second revision)
(Part 2):1999
Determination of fineness by specific surface by Blaine air permeability method (second revision)
1727:1967
Methods of test for pozzolanic materials (first revision)
Determination of fineness by specific surface by Blaine air permeability method (second revision)
IS No. Title
(Part 3) : 1988 Determination of soundness (first revision)
(Part 4) : 1988 Determination of consistency of standard cement paste (first revision)
(Part 5) : 1988 Determination of initial and final setting times (first revision)
(Part 6) : 1988 Determination of compressive strength of hydraulic cement (other than masonry cement) (first revision)
(Part 7) : 1988 Determination of compressive strength of masonry cement (first revision)
(Part 8) : 1988 Determination of transverse and compressive strength of plastic mortar using prism (first revision)
(Part 9) : 1988 Determination of heat of hydration (first revision)
(Part 10) : 1988 Determination of drying shrinkage (first revision)
(Part 11) : 1988 Determination of density (first revision)
(Part 12) : 1988 Determination of air content of hydraulic cement mortar (first revision)
(Part 14) : 1989 Determination of false set
(Part 15) : 1991 Determination of fineness by wet sieving
4032 : 1985 Methods of chemical analysis for hydraulic cement (first revision)
5816 : 1999 Method of test for splitting tensile strength of concrete (first revision)
8142 : 1976 Methods of test for determining setting time of concrete by penetration resistance
9013 : 1978 Method of making, curing and determining compressive strength of accelerated cured concrete test specimens
9284 : 1979 Method of test for abrasion resistance of concrete
12423 : 1988 Methods for colorometric analysis of hydraulic cement
12803 : 1989 Methods of analysis of hydraulic cement by X-ray fluorescence spectrometer
IS No. Title
12813 : 1989 Method of analysis of hydraulic cement by atomic absorption spectrophotometer
13311 Methods of non-destructive testing of concrete:
(Part 1) : 1992 Ultrasonic pulse velocity
(Part 2) : 1992 Rebound hammer
f) Treatment of Concrete Joints
1834 : 1984 Specification for hot applied sealing compound for joint in concrete (first revision)
1838 Specification for preformed fillers for expansion joint in concrete pavements and structures (non-extruding and resilient type):
(Part 2) : 1984 CNSL aldehyde resin and coconut pith
10566 : 1983 Methods of test for preformed fillers for expansion joints in concrete paving and structural construction
11433 Specification for one grade polysulphide based joint sealant:
(Part 1) : 1985 General requirements
(Part 2) : 1986 Methods of test
12118 Specification for two parts polysulphide based sealants:
(Part 1) : 1987 General requirements
(Part 2) : 1987 Methods of test
g) Concrete Reinforcement
432 Specification for mild steel and medium tensile steel bars and hard drawn steel wire for concrete reinforcement:
(Part 1) : 1982 Mild steel and medium tensile steel bars (third revision)
(Part 2) : 1982 Hard drawn steel wire (third revision)
1566 : 1982 Specification for hard drawn steel wire fabric for concrete reinforcement (second revision)
1608 : 1995 Mechanical testing of materials — Tensile testing
1785 Specification for plain hard drawn steel wire for prestressed concrete:
IS No.
Title
IS No.
Title
(Part 1): 1983
Cold drawn stress-relieved wire (second revision)
6073: 1971
Specification for autoclaved reinforced cellular concrete floor and roof slabs
(Part 2): 1983
As drawn wire (first revision)
1786: 1985
Specification for high strength deformed steel bars and wires for concrete reinforcement (third revision)
6441
Methods of test for autoclaved cellular concrete products:
(Part 1): 1972
Determination of unit weight or bulk density and moisture content
2090: 1983
Specification for high tensile steel bars used in prestressed concrete (first revision)
(Part 2): 1972
Determination of drying shrinkage
(Part 4): 1972
Corrosion protection of steel reinforcement in autoclaved cellular concrete
6003: 1983
Specification for indented wire for prestressed concrete (first revision)
(Part 5): 1972
Determination of compressive strength
6006: 1983
Specification for uncoated stress-relieved strand for prestressed concrete (first revision)
(Part 6): 1973
Strength, deformation and cracking of flexural members subject to bending-short duration loading test
10790
Methods of sampling of steel for prestressed and reinforced concrete:
(Part 7): 1973
Strength, deformation and cracking of flexural members subject to bending-sustained loading test
(Part 1): 1984
Prestressing steel
(Part 8): 1973
Loading tests for flexural members in diagonal tension
(Part 2): 1984
Reinforcing steel
13620: 1993
Specification for fusion bonded epoxy coated reinforcing bars
(Part 9): 1973
Jointing of autoclaved cellular concrete elements
iii) Other Fibre Cement Products
14862 : 2000 Specification for fibre cement flat sheets
14871 : 2000 Specification for products in fibre reinforced cement long corrugated or asymmetrical section sheets and fittings for roofing and cladding
iv) Concrete Pipes and Pipes Lined/Coated with Concrete or Mortar
458 : 2003 Specification for precast concrete pipes (with and without reinforcement) (fourth revision)
(Part 12) : 1977 Central loading of plate test (first revision)
IS No.
Title
IS No.
Title
(Part 13): 1977
Long time loading bending test (first revision)
iii) Wood-Based Laminates
(Part 14): 1977
Screw and nail withdrawal test (first revision)
3513 (Part 3): 1989
Specification for resin treated compressed wood laminates (compregs): Part 3 For general purposes (first revision)
(Part 15): 1977
Lateral nail resistance (first revision)
3513 (Part 4): 1966
Specification for high and medium density wood laminates (compreg): Part 4 Sampling and tests
(Part 16): 1977
Determination of water absorption (first revision)
(Part 17): 1977
Determination of swelling in water (first revision)
7638: 1998
Methods of sampling for wood/ lignocellulosic based panel products
(Part 18): 1977
Determination of mass and dimensional changes caused by moisture changes (first revision)
9307
Methods of tests for wood-based structural sandwich construction:
(Part 19): 1977
Durability cyclic test for interior use (first revision)
(Part 1): 1979
Flexure test
(Part 2): 1979
Edgewise compression test
(Part 3): 1979
Flatwise compression test
(Part 20): 1977
Accelerated weathering cyclic test for exterior use (first revision)
(Part 4): 1979
Shear test
(Part 5): 1979
Flatwise tension test
(Part 21): 1977
Planeness test under uniform moisture content (first revision)
(Part 6): 1979
Flexure creep test
(Part 7): 1979
Cantilever vibration test
(Part 22): 1981
Determination of surface glueability test
(Part 8): 1979
Weathering test
(Part 23): 1981
Vibration test for particle boards
14315: 1995
Specification for commercial veneers
3087: 1985
Specification for wood particle boards (medium density) for general purposes (first revision)
14616: 1999
Specification for laminated veneer lumber
3097: 1980
Specification for veneered particle boards (first revision)
iv) Bamboo and Coir Board Products
3129: 1985
Specification for low density particle board (first revision)
13958: 1994
Specification for bamboo mat board for general purposes
3308: 1981
Specification for wood wool building slabs (first revision)
14588: 1999
Specification for bamboo mat veneer composite for general purposes
3348: 1965
Specification for fibre insulation boards
14842: 2000
Specification for coir veneer board for general purposes
3478: 1966
Specification for high density wood particle boards
15476: 2004
Specification for bamboo and corrugated sheets
12406: 2003
Specification for medium density fibreboards for general purposes (first revision)
v) Adhesives
12823: 1990
Specification for prelaminated particle boards
848: 1974
Specification for synthetic resin adhesives for plywood (phenolic and aminoplastic) (first revision)
13745: 1993
Method for determination of formaldehyde content in particle board by extraction method called perforator method
849: 1994
Specification for cold setting case in glue for wood (first revision)
14276: 1995
Specification for cement bonded particle boards
851: 1978
Specification for synthetic resin adhesives for construction work (non-structural) in wood (first revision)
14587: 1998
Specification for prelaminated medium density fibre board
852: 1994
Specification for animal glue for general wood-working purposes (second revision)
IS No. Title
1508 : 1972 Specification for extenders for use in synthetic resin adhesives (ureaformaldehyde) for plywood (first revision)
4835 : 1979 Specification for polyvinyl acetate dispersion-based adhesives for wood (first revision)
9188 : 1979 Performance requirements for adhesive for structural laminated wood products for use under exterior exposure condition
Specification for ball catches for use in wooden almirah
2681 : 1993
Specification for non-ferrous metal sliding door bolts for use with padlocks (third revision)
8760 : 1978
Specification for mortice sliding door locks, with lever mechanism
9106 : 1979
Specification for rising butt hinges
3564 : 1995
Specification for door closers (hydraulically regulated) (second revision)
9131 : 1979
Specification for rim locks
9460 : 1980
Specification for flush drop handle for drawer
3818 : 1992
Specification for continuous (piano) hinges (third revision)
9899 : 1981
Specification for hat coat and wardrobe hooks
3828 : 1966
Specification for ventilator chains
10019 : 1981
Specification for mild steel stays and fasteners
3843 : 1995
Specification for steel backflap hinges (first revision)
10090 : 1982
Specification for numericals
3847 : 1992
Specification for mortice night latches (first revision)
10342 : 1982
Specification for curtain rail system
12817 : 1997
Specification for stainless steel butt hinges (first revision)
4621 : 1975
Specification for indicating bolts for use in public baths and lavatories (first revision)
12867 : 1989
Specification for PVC hand rails covers
4948 : 2002
Specification for welded steel wire fabric for general use (second revision)
14912 : 2001
Specification for door closers concealed type (hydraulically regulated)
(Part 8/Sec 6):1993
Tests for pigments and other solids, Section 6 Volume solids
(Part 9/Sec 1):1993
Tests for lacquers and varnish, Section 1 Acid value
3536:1999
Specification for ready mixed paint, brushing, wood primer (first revision)
(Part 9/Sec 2):1993
Tests for lacquers and varnish, Section 2 Rosin test
3537:1966
Specification for ready mixed paint, finishing, interior for general purposes, to Indian Standard colours No. 101, 216, 217, 219, 275, 281, 352, 353, 358 to 361, 363, 364, 388, 410, 442, 444, 628, 631, 632, 634, 693, 697, white and black
Specification for ready mixed paint, brushing, priming, plaster to Indian Standard colours No. 361 and 631 (first revision)
3539:1966
Specification for ready mixed paint, undercoating, for use under oil finishes, to Indian Standard colours, as required
123:1962
Specification for ready mixed paint, brushing, finishing, semi-gloss, for general purposes, to Indian Standard colours No. 445, 446, 448, 449, 451 and 473; and red oxide (colour unspecified) (revised)
3585:1966
Specification for ready mixed paint, aluminium, brushing, priming, water resistant, for wood work
3678 : 1966
Specification for ready mixed paint, thick white, for lettering
18. POLYMERS, PLASTICS AND GEOSYNTHETICS/GEOTEXTILES
18. POLYMERS, PLASTICS AND GEOSYNTHETICS/GEOTEXTILES
8662 : 1993
Specification for enamel, synthetic, exterior, (a) undercoating, (b) finishing, for railway coaches (first revision)
1998 : 1962
Methods of test for thermosetting synthetic resin bonded laminated sheets
9862 : 1981
Specification for ready mixed paint, brushing, bituminous black lead free, acid, alkali, water and chlorine resisting
2036 : 1995
Specification for phenolic laminated sheets (second revision)
9862 : 1981
Specification for ready mixed paint, brushing, bituminous black lead free, acid, alkali, water and chlorine resisting
Specification for ready mixed paint, brushing, red oxide, priming for metals
2076 : 1981
Specification for unsupported flexible vinyl film and sheeting (first revision)
13183 : 1991
Specification for aluminium paints, heat resistant
2508 : 1984
Specification for low density polyethylene films (second revision)
13213 : 1991
Specification for polyurethane full gloss enamel (two pack)
2508 : 1984
Specification for low density polyethylene films (second revision)
13607 : 1992
Specification for ready mixed paint, finishing, general purposes, synthetic
6307 : 1971
Specification for rigid PVC sheets
13607 : 1992
Specification for ready mixed paint, finishing, general purposes, synthetic
9766 : 1992
Specification for flexible PVC compound (first revision)
13871 : 1993
Specification for powder coatings
10889 : 1984
Specification for high density polyethylene films
c) Thinners and Solvents
c) Thinners and Solvents
c) Thinners and Solvents
c) Thinners and Solvents
82 : 1992
Methods of sampling and test for thinners and solvents for paints (first revision)
12830 : 1989
Specification for rubber based adhesives for fixing PVC tiles to cement
324 : 1959
Specification for ordinary denatured spirit (revised)
13162
Methods of test for geotextiles:
324 : 1959
Specification for ordinary denatured spirit (revised)
(Part 2) : 1991
Determination of resistance to exposure of ultra-violet light and water (Xenon arc type apparatus)
533 : 1998
Specification for gum spirit of turpentine (oil of turpentine) (second revision)
(Part 3) : 1992
Determination of thickness at specified pressure
14314 : 1995
Specification for thinner general purposes for synthetic paints and varnishes
(Part 4) : 1992
Determination of puncture resistance by falling cone method
14314 : 1995
Specification for thinner general purposes for synthetic paints and varnishes
(Part 5) : 1992
Determination of tensile properties using a wide width strip
d) Varnishes and Lacquers
d) Varnishes and Lacquers
d) Varnishes and Lacquers
d) Varnishes and Lacquers
337 : 1975
Specification for varnish, finishing, interior (first revision)
13262 : 1992
Specification for pressure sensitive adhesive tapes with plastic base
347 : 1975
Specification for varnish, shellac, for general purposes (first revision)
13325 : 1992
Method of test for the determination to tensile properties of extruded polymer geogrids using the wide strip
348 : 1968
Specification for French polish (first revision)
13326 (Part 1) : 1992
Method of test for the evaluation of interface friction between geosynthetics and soil: Part 1 Modified direct shear technique
524 : 1983
Specification for varnish, finishing, exterior, synthetic (second revision)
13326 (Part 1) : 1992
Method of test for the evaluation of interface friction between geosynthetics and soil: Part 1 Modified direct shear technique
525 : 1968
Specification for varnish, finishing, exterior and general purposes (first revision)
14182 : 1994
Specification for solvent cement for use with unplasticized polyvinylchloride plastic pipe and fittings
642 : 1963
Specification for varnish medium for aluminium paint (revised)
14182 : 1994
Specification for solvent cement for use with unplasticized polyvinylchloride plastic pipe and fittings
15060 : 2001
Tensile test for joints/seams by wide width method of geotextiles
407 : 1981
Specification for brass tubes for general purposes (third revision)
15060 : 2001
Tensile test for joints/seams by wide width method of geotextiles
2501 : 1995
Specification for solid drawn copper tubes for general engineering purposes (third revision)
19. SANITARY Fittings
APPLIANCES AND WATER
a) General
ii) Cast Iron Pipes and Fittings
ii) Cast Iron Pipes and Fittings
775 : 1970
Specification for cast iron brackets and supports for wash basins and sinks (second revision)
1536 : 2001
Specification for centrifugally cast (spun) iron pressure pipes for water, gas and sewage (fourth revision)
782 : 1978
Specification for caulking lead (third revision)
1537 : 1976
Specification for vertically cast iron pressure pipes for water, gas and sewage (first revision)
804 : 1967
Specification for rectangular pressed steel tanks (first revision)
1538 : 1993
Specification for cast iron fittings for pressure pipes for water, gas and sewage (third revision)
1700 : 1973
Specification for drinking fountains (first revision)
1729 : 2002
Specification for sand cast iron spigot and socket soil, waste and ventilating pipes, fittings and accessories (second revision)
2963 : 1979
Specification for copper alloy waste fittings for wash-basins and sinks (first revision)
3489 : 1985
Specification for enamelled steel bath tubs (first revision)
IS No.
Title
IS No.
Title
1879 : 1987
Specification for malleable cast iron pipe fittings (second revision)
12988 : 1991
Rubber sealing rings for CID joints for light duty AC pipes — Dimensional requirements
3486 : 1966
Specification for cast iron spigot and socket drain pipes
13382 : 1992
Cast iron specials for mechanical and push on flexible joints for pressure pipelines for water, gas and sewage
3989 : 1984
Specification for centrifugally cast (spun) iron spigot and socket soil, waste and ventilating pipes, fittings and accessories (second revision)
5531 : 1988
Specification for cast iron specials for asbestos cement pressure pipes for water, gas and sewage (second revision)
404 (Part 1) : 1993
Specification for lead pipes: Part 1 For other than chemical purpose (third revision)
6163 : 1978
Specification for centrifugally cast (spun) iron low pressure pipes for water, gas and sewage (first revision)
iv) Fibre Pipes and Fittings
iv) Fibre Pipes and Fittings
6163 : 1978
Specification for centrifugally cast (spun) iron low pressure pipes for water, gas and sewage (first revision)
11925 : 1986
Specification for pitch-impregnated fibre pipes and fittings for drainage purposes
6418 : 1971
Specification for cast iron and malleable cast iron flanges for general engineering purposes
v) Plastic Pipes and Fittings
v) Plastic Pipes and Fittings
6418 : 1971
Specification for cast iron and malleable cast iron flanges for general engineering purposes
3076 : 1985
Specification for low density polyethylene pipes for potable water supplies (second revision)
7181 : 1986
Specification for horizontally cast iron double flanged pipes for water, gas and sewage (first revision)
4984 : 1995
Specification for high density polyethylene pipes for water supply (fourth revision)
8329 : 2000
Specification for centrifugally cast (spun) ductile iron pressure pipes for water, gas and sewage (third revision)
4985 : 2000
Specification for unplasticized PVC pipes for potable water supplies (third revision)
8794 : 1988
Specification for cast iron detachable joints for use with asbestos cement pressure pipes (first revision)
7834
Specification for injection moulded PVC socket fittings with solvent cement joints for water supplies:
9523 : 1980
Specification for ductile iron fittings for pressure pipes for water, gas and sewage
(Part 1) : 1987
General requirements (first revision)
9523 : 1980
Specification for ductile iron fittings for pressure pipes for water, gas and sewage
(Part 2) : 1987
Specific requirements for 45° elbows (first revision)
10292 : 1988
Dimensional requirements for rubber sealing rings for CID joints in asbestos cement piping (first revision)
(Part 3) : 1987
Specific requirements for 90° elbows (first revision)
10292 : 1988
Dimensional requirements for rubber sealing rings for CID joints in asbestos cement piping (first revision)
(Part 4) : 1987
Specific requirements for 90° tees (first revision)
10299 : 1982
Cast iron saddle pieces for service connection from asbestos cement pressure pipes
(Part 5) : 1987
Specific requirements for 45° tees (first revision)
11606 : 1986
Methods of sampling cast iron pipes and fittings
(Part 6) : 1987
Specific requirements for sockets (first revision)
12820 : 1989
Dimensional requirements of rubber gaskets for mechanical joints and push on joints for use with cast iron pipes and fittings for carrying water, gas and sewage
(Part 7) : 1987
Specific requirements for unions (first revision)
12820 : 1989
Dimensional requirements of rubber gaskets for mechanical joints and push on joints for use with cast iron pipes and fittings for carrying water, gas and sewage
(Part 8) : 1987
Specific requirements for caps (first revision)
12987 : 1991
Cast iron detachable joints for use with asbestos cement pressure pipes (light duty)
8008
Specification for injection moulded high density polyethylene (HDPE) fittings for potable water supplies:
12987 : 1991
Cast iron detachable joints for use with asbestos cement pressure pipes (light duty)
(Part 1) : 2003
General requirements
(Part 3): 1988
Specific requirements of straight reducers (first revision)
13592: 1992
Specification for UPVC pipes for soil and waste discharge systems inside buildings including ventilation and rainwater system
(Part 4): 1988
Specific requirements for caps (first revision)
14333: 1996
Specification for high density polyethylene pipes for sewerage
(Part 5): 1988
Specific requirements for equal tees (first revision)
14402: 1996
Specification for GRP pipes, joints and fittings for use for sewerage, industrial waste and water (other than potable)
(Part 6): 1988
Specific requirements for flanged tail piece with metallic flanges (first revision)
(Part 7): 1988
Specific requirements for threaded adaptors (first revision)
14735: 1999
Specification for unplasticized polyvinyl chloride (UPVC) injection moulded fittings for soil and waste discharge system for inside buildings including ventilation and rain water system
(Part 8): 1988
Specific requirements for 90° bends (first revision)
(Part 9): 1988
Specific requirements for 60° bends (first revision)
14885: 2001
Specification for polyethylene pipe for supply of gaseous fuel
(Part 10): 1988
Specific requirements for 45° bends (first revision)
15225: 2002
Specification for chlorinated polyvinyl chloride compounds used for pipes and fittings
(Part 11): 1988
Specific requirements for 30° bends (first revision)
(Part 12): 1988
Specific requirements for 221⁄2° bends (first revision)
15328: 2003
Specification for unplasticized non-pressure polyvinyl chloride (PVC-U) pipes for use in underground drainage and sewerage system
(Part 13): 1988
Specific requirements for 111⁄4° bends (first revision)
4038:1986
Specification for foot valves for water works purposes (second revision)
(Part 15):1995
Specific requirements of universal water closets (first revision)
4346:1982
Specification for washers for use with fittings for water services (first revision)
(Part 16):2002
Specific requirements for wash down wall mounted water-closets
(Part 17):1995
Specific requirements for wall mounted bidets
5312
Specification for swing check type reflux (non-return) valves:
5961:1970
Specification for cast iron gratings for drainage purposes
(Part 1):1984
Single door pattern (first revision)
(Part 2):1986
Multi-door pattern
7231:1984
Specification for plastic flushing cisterns for water-closets and urinals (second revision)
8931:1993
Specification for cast copper alloy fancy single tap combination tap and stop valves for water services (first revision)