Introduction
The storage of rain water on surface is a traditional technique and the structures used were underground tanks, ponds, check dams, weirs etc. Recharge to ground water is a new concept of rain water harvesting and the structures generally used are:-
a. Pits: Recharge pits are constructed for recharging the shallow aquifer. These are constructed 1 to 2m, wide and to 3m deep which are back filled with boulders, gravels, coarse sand.
b. Trenches: These are constructed when the permeable stream is available at shallow depth. Trench may be 0.5 to 1m. wide, 1 to 1.5m deep and 10 to 20m long depending up availability of water. These are back filled with filler materials.
c. Dug wells: Existing dug wells may be utilized as recharge structure and water should pass through filter media before putting into dug well.
d. Hand pumps: The existing hand pumps may be used for recharging the shallow/deep aquifers, if the availability of water is limited. Water should pass through filter media before diverting it into hand pumps.
e. Recharge wells: Recharge wells of 100 to 300 mm. diameter are generally constructed for recharging the deeper aquifers and water is passed through filter media to avoid choking of recharge wells.
f. Recharge Shafts: For recharging the shallow aquifer which are located below clayey surface, recharge shafts of 0.5 to 3 m. diameter and 10 to 15 m. deep are constructed and back filled with boulders, gravels & coarse sand.
g. Lateral shafts with bore wells: For recharging the upper as well as deeper aquifers lateral shafts of 1.5 to 2 m. wide & 10 to 30 m. long depending upon availability of water with one or two bore wells are constructed. The lateral shafts are back filled with boulders, gravels & coarse sand.
h. Spreading techniques: When permeable strata start from top then this technique is used. Spread the water in streams/nallah by making check dams, nallah bunds, cement plugs, gabion structures or a percolation pond may be constructed.
Procedure for Installation Rain Water Harvesting
- The following provisions shall be applicable for installation of Rain Water Harvesting Structures
1.1 Provision of Rain Water Harvesting shall be mandatory for plot of size 100 sqm and above.
1.2 The building construction could be broadly classified as per the following:
1.2.1 Category - (A) Building on plot size less than 100 sqm.
1.2.2 Category - (B) Building up to G-2 on the plot size more than 100 sqm.
1.3 Category-© Building G+3 and above on plot size more than 100 sqm.
1.4 The Rain Water Harvesting arrangement is not mandatory for building with a plot size less than 100 sqm. However, the owners of buildings are advised to construct Rain Water Harvesting structure for conservation and protection of ground water. Either they adopt traditional method or any upgrade method.
1.5 All the layout open spaces / amenity spaces of housing societies and new constructions / reconstruction’s Authority may approve the Rain Water Harvesting structures of specifications different from those specified here with, subject to the minimum capacity of rain water harvesting being ensured in each case.
Annexure E
Annexure & Appendices
1.6 The owner / society of every building mentioned in the para 1.5 above shall ensure that the Rain Water Harvesting structure is maintained in good condition for storage of water for non-potable purposes or recharge of groundwater at all times.
1.7 The Authority may impose a levy for the failure of the owner of any building mentioned in the para 1.5 above to provide or to maintain Rain Water Harvesting structures and when required.
1.8 Rain Water Harvesting shall be made mandatory for every Urban Local Bodies/Planning Authority to identify, demarcate, protect and maintain the water bodies that come under their jurisdiction will prepare a list.
1.9 If Rain water Harvesting system has not been installed in the apartments/houses having area less than 100 sqm, constructed before 2019 and there is no space available for installation of the same, the issue will be heard and resolved by the concerned Development Authority and suitable order shall be passed from case to case by The CEO/ Executive officer/special offer of the Development Authority/ ULBs.
1.10 It is the responsibility of the builders of the apartments to install rain water harvesting structure, if the building is constructed on or after 2019 and the occupancy certificate has been procured from the Director of Town Planning/ Development Authority than the owner of the flats will have combined responsibility to install rain water harvesting in the building.
2. Rain Water Harvesting in a Building Site.
Includes storage or recharging into ground the rain water falling on the terrace or on any paved or unpaved surface within the building site.
2.1 The following systems may be adopted for harvesting the rain water drawn from terrace and the paved surface.
2.1.1 Open well of a minimum of 1.00 mdia and 6 m in depth into which rain water may be channeled and allowed after filtration for removing silt and floating material. The well shall be provided with ventilating covers. The water from the open well may be used for non-potable domestic purposes such as washing, flushing and for watering the garden etc.
2.1.2 Rain Water Harvesting for recharge of ground water may be done through a bore well around which a pit may be excavated up to a depth of atleast 3.0 m and refilled with stone aggregate and sand. The filtered rain water may be channeled to the refilled pit for recharging the bore well.
2.1.3 An impervious surface / underground storage tank of required capacity may be constructed in the setback or other open space and the rain water may be channeled to the storage tank. The storage tank shall suitably placed so that the rain water may be drawn off for domestic, washing gardening and such other purposes. The storage tanks shall be provided with an overflow.
2.1.4 The surplus rain water after storage may be recharged into ground through percolation pits or trenches or combination of pits and trenches. Depending on the geographical and topographical condition, the pits may be of the size of 1.20 mt. width x 1.20mt length x 2.00 mt. to 2.50 mt. depth. The tranches can be or 0.60 mt width x 2.00 to 6.00 mt. length x 1.50 to 2.00 mt. depth. The capacity/ volume and number of pits and trenched should depend upon the catchment area and quantity of peak rain fall of the area. It can vary from place to place. Terrace water shall be channelled to pits or trenches. Such pits or trenches shall be back filled with filter media comprising the following materials.
2.1.4.1 40 mm stone aggregate as bottom layer upto 25% of the depth;
2.1.4.2 20 mm stone aggregate as lower middle layer upto 25% of the depth;
2.1.4.3 Coarse sand as upper middle layer upto 40% of the depth;
2.1.4.4 A thin layer of fine sand as top layer.
2.1.5 Top 10% of the pits / trenched will be empty and a splash is to be provided in this portion in such a way that roof top water falls on the splash pad.
2.1.6 Brick masonry wall is to be constructed on the exposed surface of pits / trenches and the cement mortar plastered.
Annexure E
Annexure & Appendices
2.1.7 The depth of wall below ground shall be such that the wall prevents lose soil entering into pits / trenched. The projection of the wall above ground shall at least be 15 cms.
2.1.8 Perforated concrete slabs shall be provided on the pits / trenches. Bund should be created to minimize the run off.
A common rain water harvesting structure shall be installed for a cluster of houses/buildings where there is no space for making a rain water harvesting structure. It shall be the duty of each and every owner / occupier to participate in the installation and maintenance of community rain water harvesting.
4 Rain Gardens
A rain garden is a functional landscaping technique that can beautify our property as well as help to filter and slow the flow of storm water. Rain gardens allow about 30% more rainwater to soak into the ground than traditional lawns.
4.1 Rain gardens are saucer shaped gardens that water flows into that are planted with grassed, flowers, shrubs, and sometimes small trees. They soak up water while providing wildlife habitat. The soil and basin fills with water for a short amount of time before soaking back into the surrounding soil. Plants used in these gardens are adapted to survive in short periods of flooding as well as dry soils in between storms.
4.2 They are strategically located to capture runoff hard surfaces such as a driveway, parking area, sidewalk of streets. Rain gardens fill with a few inches of water after a storm and then water filters into the surrounding soil, rather than running off to the street or storm culvert.
4.3 Rain gardens are a very good option to help lower the impact of impervious surfaces and polluted runoff because they are low-tech, inexpensive, sustainable and aesthetically pleasing.
4.4 There are multiple benefits of rain garden to the community and the local environment which include:
4.4.1 Reduced polluted storm water runoff from yards into local streams,
4.4.2 Reduced localized flooding,
4.4.3 Reduced erosion,
4.4.4 Pollution prevention,
4.4.5 Groundwater recharge,
4.4.6 Enhanced wildlife habitat,
Annexure E
Annexure & Appendices