10.1 Internal Road and Approach to Building and Common Plot
-
Internal road width shall be measured from its origin to the next wider road it meets.
-
In case of single building the width of approach/ internal road shall be measured based on the distance from the TP or DP road up to the edge of the building in case of hollow plinth, or location of the farthest entrance of a building in case of solid plinth. In case of buildings connected internally or externally the length of internal road shall be considered up to the edge of the hollow plinth of the farthest building (in case of building with hollow plinth) and up to the location of the farthest entrance of the building in case of solid plinth.
-
In case of layout with two or more buildings of such as apartment, hostel, dharmashala, cottage industry units, commercial units or independent establishments, the width of Internal Road on which the building abuts shall be as applicable for a length of above 45.00 m. In case of more than two buildings including detached dwelling unit, semi-detached dwelling unit, row house, tenament, etc. approach of as applicable width shall be allowed up to the second dwelling unit.
-
The width of the Internal or Approach Road shall be based on the length and use of the Buildingunit as under:
| Sr. No. | ROAD LENGTH (m) | WIDTH OF ROAD FOR RESIDENTIAL USE (m) | WIDTH OF ROAD FOR COMMERCIAL, INDUSTRIAL AND OTHER NON RESIDENTIAL USE(m) |
|---|---|---|---|
| 1 | Up to 150 | 7.50 | 9.00 |
| 2 | Above 150 and up to 300 | 9.00 | 12.00 |
| 3 | Above 300 | 10.50 | 15.00 |
| 4 | Above 450 | 12.00 | 18.00 |
If margin required is bigger than width of Approach Road or Internal Road whichever is higher shall be applicable.
10.2 General Requirements for Internal Roads
-
The Internal Road shall be provided up to each individual building.
-
Internal road width shall be measured in length from the farthest point of its origin to the next wider road it meets.
-
In cases where the road is in continuation with any private road in the adjoining estate or any public road continuous to the estate, the length of the adjoining road of the public road shall be added to the length of the internal road for the purpose of determining the width of such road.
-
Curves at the junction: The curves shall be provided at the junction of roads as prescribed below:
GDCR 2016
| Sr. No. | WIDTH OF THE ROAD(m) | RADIUS OF ROAD CURVATURE (m) |
|---|---|---|
| 1 | Less than 7.50 | 4.50 |
| 2 | More than 7.50 and up to 18.00 | 6.00 |
| 3 | More than 18.00 | 7.50 |
The width of the wider road shall be taken into consideration in determining the radius of the curvature at the junction of roads of different widths.
-
The shape of the plots and the junction of the roads, at the corners shall be designed as directed by the Competent Authority.
-
The alignment of the internal road or roads shall be regulated to be in continuation of the public or private roads continuous to the applicant's Building Unit; but in case of termination of an internal road or roads; a turning circle with diameter of 13.50 m or 12.00 m x 6.00 m turning "T" shall be required at the cul-de-sac. This requirement may be waived for such road with width of 7.50 m if the length does not exceed 110.00 m.
-
The Development Permission shall be regulated as per the proposed road network by the competent authority.
-
For development area in non-T.P. area, the width of one road shall be decided by the Competent Authority.
10.3 Amalgamation and Subdivision of Building-unit
The owner or developer shall be required to get the land reconstituted by the Competent Authority as ‘Building-unit’ or ‘Building-units’ before amalgamation or subdivision of the land. Development Permission shall not be granted without fulfilment of this requirement.
Amalgamation shall be allowed provided that it is not violative of existing laws enforced and provisions of The Town Planning Act and The Stamp Duty Act.
10.4 Amalgamation and Subdivision of Building-unit with Existing Structures
In the case of Building-units with existing buildings, its sub-division or amalgamation shall not be approved unless it fulfils all the requirements under these Regulations.
10.5 Development on Kabrastan, Burial Ground, ETC.
The land occupied by the graveyards, kabrastans, burial grounds, crematoria and allied actions in the Development Plan shall be kept permanently open. Competent Authority may permit structures to be built for specific purpose.
No land shall be used for kabrastans, burial grounds without prior permission of the Surat District Collector and duly identified and demarcated on ground by the Competent Authority.
10.6 Internal Building Layout in a Building Unit
In the case of a building unit which is intended to be developed with internal roads, buildings, and other structures, no development permission shall be issued to the owner or the person who has right to develop it, unless the said owner or person who has right to develop has applied and has got the internal layout approved by the Competent Authority as per these Regulations.
10.7 Level of Building Unit
The general level of the building unit shall not be lower than the level of the crown of the road in front. Provided that in the case of plot, the level of which is lower than the crown of the road in front and which in the opinion of the Competent Authority, could be drained off in the storm water drainage and sewer, the competent Authority may permit a suitable lower level.
10.8 Notional Plots
In case of mixed Development of Low rise building & High rise building the F.S.I shall be Computed on the basis of notional building unit form by subdivision by such notional plots boundary between low rise building and high rise building subject to other regulations. Such notional plot boundary means imaginary boundary from building after leaving the required margin.