(a) Chain shall not be used for the suspension of lift. For car or counterweight of any lift with traction drive, the number of independent suspension ropes shall not be less than four for 8mm diameter ropes, and shall not be less than three for 10mm and above diameter ropes.
(b) Each suspension rope shall be separately and independently fixed to the car and to the counter-weight. The simple suspension of the liftcar or the counter-weight by means of a sheave or the like shall count as one suspension only.
(c) All ropes anchored to a winding drum shall have not less than one and one half turns of the ropes on the winding drum when the lift-car or counter-weight has reached the extreme limit of its over-travel.
(d) The winding drum end of the lift-car and counter-weight ropes shall be secured by clamps on the inside of the drum.
(e) Every lift-car or counter-weight rope shall be in one length and free from joints.
(f) The materials quality, construction and fixing of ropes shall, so far as is applicable, conform to the appropriate British Standard specification.
(g) The factor of safety of the combined suspension ropes shall be not less than 12 based on static contract load plus the weight of the lift car and accessories.
(h) The lift-car and counter-weight ends of the suspension ropes shall be fastened by spliced return loops, clipped return loops or individual tapered babbitted sockets. Loops, shall not bear directly on their fixings, but shall be lined with proper thimbles, eyes or equal protection. In all cases, the fastenings shall be capable of sustaining a load of not less than 80 percent of the minimum breaking strength of the suspension rope.
(i) Means shall be provided for adjusting the lengths of the ropes to equalize the load of the individual suspension ropes. No equalizer shall be used unless the equalizer and its fastenings, in its several parts and assembly, have strength of at least 10 per cent, in excess of the strength of the cable required by clause (h).
(j) Tensioning devices for compensating ropes, governor ropes and the like shall be protected against damage due to falling objects.
(k) The minimum diameter of ropes for car and counterweight of passenger and goods lifts shall be 8 mm.
- Emergency Safety Devices.— (a) Every lift shall be provided with a lift-car safety gear, attached to the lift-car frame and placed beneath the carplatform. The safety gear shall be capable of stopping and sustaining the liftcar with full contract load in the lift-car.
(b) The application of the safety gear’ shall not cause the car-platform to become out of level in excess of (6mm) per foot measured in any direction.
(c) No safety gear shall be permitted to stop an ascending lift-car or counter-weight, if an ascending lift-car is to be stopped on account of over speed, a safety gear shall be fitted to the counter-weight for this purpose. The governor may, however, open the motor circuit and apply the brake in the event of over speed in the ascending direction.
(d) When the safety gear is applying no decrease in the tension of any rope for applying the safety gear or motion of the lift-car in the descending direction shall release the safety gear. It is permissible to release the safety gear by reversing direction of the lift machine.
(e) When a safety gear comes into operation, it shall automatically open the operating circuit, and it shall be possible for a reasonable person to
release the safety gear after a thorough inspection of the equipment and the taking of necessary precautions.
(f) The safety gear shall operate to stop and sustain the lift-car in the event of failure of the suspension ropes, or in the event of the lift exceeding a predetermined maximum speed in the descending direction when a speed governor is fitted.
(g) Every safety gear shall operate positively and mechanically independently of any springs used in its construction.
(h) Any levers or dogs operated by shafts shall be keyed to such shafts by clause 18 of Indian standard Specification No.4666-1968) keys or fixed by some other equally secure device approved by the Chief Engineer (Elect.) or Superintending Engineer (Elect.) HP PWD., Shimla( HP).
(i) The design of the safety gear shall provide for its application to both guides and to each side of such guides equally.
(j) Any rope used for applying the safety gear shall be led over independents pulleys running on independent shafts and properly guarded. Such ropes shall be not less than (6mm) in diameter and shall be of steel or phosphor bronze.
(k) It shall not be possible for vibrations of the lift-car frame to cause the safety gear to be applied.
(l) Any part of a safety gear subject to tension, torsion or bending shall be made of steel.
(m) All bearings for drums and screw shafts in connection with the safety gears shall be of non-ferrous metals.
(n) Car and counter weight safety devices shall be actuated by separate governors. Provision shall be made to cause the application of the counter-weight safety gear at not more than 10 percent in excess of hat at which the lift-car safety gear applies.
(o) The types of safety gear shall be of the following kinds, namely:
(i) Instantaneous type limited to speed not exceeding 200 feet per minute (Type I).
(ii) Gradual wedge clamp type with gradual increasing retarding force (G.W.C).
(iii) Flexible guide clamp type with constant retarding force (F.G.C)
(iv) Combination of Instantaneous and oil buffer safety for speed not exceeding 2.5 meters per second.
(p) Safety gears designed to stop the lift-car or counter-weight in a distance elated to the car or counter-weight speed shall stop the lift-car with rated load or the counter-weight from the governor tripping speed within the range of stopping distances given in the Table below.
Explanation.—For the purpose of this sub-clause” the stopping distance” means the actual slide as observed from the markings on the guides made by the safety gear.
TABLE
| Sr.No. | Governor tripping speed in meters per second. | Stopping distance in millimeter | |
| Maximum | Minimum | ||
| 1. | 0.88 | 368 | 161 |
| 2. | 1.00 | 401 | 173 |
| 3. | 1.25 | 482 | 202 |
| 4. | 1.5 | 582 | 237 |
| 5. | 1.75 | 700 | 278 |
| 6. | 2.00 | 836 | 326 |
| 7. | 2.25 | 990 | 380 |
| 8. | 2.5 | 1162 | 441 |
Note.—The following formula shall be used to determine the maximum stopping distances for gradual wedge clamp and flexible guide clamp type safeties for lift-car and counter-weight for all intermediate speeds:—
S1 = 245 V2+256
In this formula, ‘ S1 represents the maximum stopping distance in millimeters ‘S2’ represents the minimum stopping distance in millimeters and ‘V’ represents governor tripping speeds in meters per second.
(q) The rope attached to any safety gear actuating drum shall have not less than two turns of rope remaining on the drum after the safety jaws have gripped the guides and stopped the lift-car.
(r) No safety gear shall depend on the completion or maintenance of an electric circuit for its operation. All safety gears shall be applied mechanically.
(s) The gripping surfaces of lift-car of counter-weight safety gears shall not be used to guide the lift-car or counter-weight but shall run free of the guides during normal operation of the lift.
Note.—A pawl or arched shall not be held to constitute a sufficient safety gear for lifts traveling in a vertical or substantially vertical direction.
- Over speed Governor.—(i) Tripping of the Over speed Governor for the car safety gear shall be adjusted as indicated below:—
(a) Not less than 115 percent of rated speed.
(b) For rated speed of 1 m/s or less, maximum governor tripping speed shall be 140 percent of the rated speed or 0.88 m/s, whichever is higher.
(c) For the rated speed of above 1 m/s, the maximum; governor tripping speed shall be 115 percent of the rated speed plus 0.25 m/s.
(ii) Choice of Tripping Speed.- (a) for lifts where the rated speed exceeds 1 m/s, it is recommended to choose a tripping speed as close as possible to the upper limit indicated in 4.1.
(b) For lifts with very heavy rated loads and low rated speeds, the over speed governor shall be specially designed for this purpose. It is recommended to choose a tripping speed as close as possible to the lower limit indicated in 4.1
(iii) The tripping speed of an over speed governor for a counterweight safety gear shall be higher than that for the car safety gear, not, however, exceeding it by more than 10 percent.
(iv) The tensile force in the over speed governor type produced by the governor, when tripped, shall be at least the greater of the following two values:—
(a) Either 300 N,or
(b) Twice the force necessary to engage the safety gear.
(v) The direction of rotation, corresponding to the operation of the safety gear, shall be marked on the over speed governor.
(vi) Over speed governor ropes.—(a) the over speed governor shall be driven by a very flexible wire rope.
(b) The braking load of the rope shall be related by a safety factor of at least 8 to the tensile force produced in the rope of the over speed governor when tripped.
(c) The nominal rope diameter shall be not less than 6mm.
(d) The ratio between the pitch circle diameter of the over speed governor pulley and the nominal rope diameter shall be at least 30.
(e) The rope shall be tensioned by a tensioning pulley.
(f) During the engagement of the safety gear, the governor rope and its attachments shall remain intact, even in the case of a braking distance greater than normal.
(g) The rope shall be easily detachable from the safety gear.
(vii) Response Time .- The response time of the over speed governor before tripping shall be sufficiently short not to permit a dangerous speed to be reached before the movement of safety gear operation.
(viii) Accessibility.-The over speed governor shall be completely accessible in all circumstances.
(ix) Possibility of Tripping the over speed Governor.— During checks or tests, it shall be possible to operate the safety gear at a lower speed than that indicated in 16.1 by tripping the over speed governor in some way.
(x) The means of adjusting the over speed governor shall be sealed after setting the tripping speed.
(xi) Speed Governor Over Speed Switch and Car Safety Gear Switch.—
(a) Switch shall be provided on the speed governor and operated by the over speed action of the governor for car speeds above 1.0m/s and when use with counterweight safeties. Every car safety shall be provided with a switch on top of the car and operated by the car safety mechanism. These switches shall, when operated, disconnect power supply from the driving machine motor and brake before or at the time of application of the safety.
(b) Switches shall be positively opened. When operated by speed governor or car safety mechanism they shall remain in the open position until manually reset after car safety mechanism has been returned to the off position.
(c) The setting of the car speed governor over speed switch shall conform to the following:—
(i) For rated speed more than 1.0 m/s, the car speed governor over speed switch shall open in the down direction of the lift at not more than 90 percent of the speed at which the governor is set to trip in the down direction.
(ii) For rated speed more than 2.5 m/s, the car speed governor over speed switch shall open in the downward direction of the lift at not more than 95 percent of the speed at which the governor is set to trip in the downward direction.
(iii) The switch when set as above, shall open in the upward direction at not more than 100 percent of the speed at which the governor is set to trip in the downward direction.