*(The regulations marked by an asterisk under these sections shall be subject to the approval of the State Government at a later stage as and when deemed fit)
43 Structural Design
For any building under the jurisdiction of these regulations structural design/ retrofitting shall only be carried out by a Structural Engineer on Record (SER) or Structural Design Agency on Record (SDAR). Proof checking of various designs/ reports shall be carried out by competent authority as per Table-1 wherever applicable.
Generally, the structural design of foundations, elements of masonry, timber, plain concrete, reinforced concrete, pre-stressed concrete and structural steel shall conform to the
provisions of part VI Structural Design Section – 1 Loads, Section – 2 Foundation, Section – 3 Wood, Section – 4 Masonry, Section – 5 Concrete & Section – 6 Steel of National Building Code of India (NBC), taking into consideration the Indian Standards as given below:
For General Structural Safety:
(i) IS: 456:2000 “Code of Practice for Plain and Reinforced Concrete.
(ii) IS: 800-1984 “Code of Practice for General Construction in Steel.
(iii) IS: 801-1975 “Code of Practice for Use of Cold Formal Light Gauge Steel Structural Members in General Building Construction.
(iv) IS 875 ( Part 2):1987Design loads ( other than earthquake ) for buildings and structures Part2 Imposed Loads.
(v) IS 875 ( Part 3):1987Design loads ( other than earthquake ) for buildings and structures Part 3 Wind Loads.
(vi) IS 875 ( Part 4):1987Design loads ( other than earthquake ) for buildings and structures Part 4 Snow Loads.
(vii) IS 875 ( Part 5):1987Design loads ( other than earthquake ) for buildings and structures Part 5 special loads and load combination.
(viii) IS: 883:1966 “Code of Practice for Design of Structural Timber in Building
(ix) IS: 1904:1987 “Code of Practice for Structural Safety of Buildings: Foundation”.
(x) IS1905:1987 “Code of Practice for Structural Safety of Buildings: Masonry Walls
(xi) IS 2911 (Part 1): Section 1: 1979 “Code of Practice for Design and Construction of Pile Foundation Section 1
Part 1: Section 2 Based Cast-in-situ Piles
Part 1: Section 3 Driven Precast Concrete Piles
Part 1: Section 4 Based precast Concrete Piles
Part 2: Timber Piles
Part 3 Under Reamed Piles
Part 4 Load Test on Piles
For Cyclone/Wind Storm Protection:
(xii) IS 875 (3)-1987 "Code of Practice for Design Loads (other than Earthquake) for Buildings and Structures, Part 3, Wind Loads"
(xiii) Guidelines (Based on IS 875 (3)-1987) for improving the Cyclonic Resistance of Low rise houses and other building
For Earthquake Protection:
(xiv) IS: 1893-2002 "Criteria for Earthquake Resistant Design of Structures (Fifth Revision)"
(xv) IS:13920-1993 "Ductile Detailing of Reinforced Concrete Structures subjected to Seismic Forces - Code of Practice"
(xvi) IS:4326-1993 "Earthquake Resistant Design and Construction of Buildings - Code of Practice (Second Revision)"
(xvii) IS:13828-1993 "Improving Earthquake Resistance of Low Strength Masonry Buildings - Guidelines"
(xviii) IS:13827-1993 "Improving Earthquake Resistance of Earthen Buildings - Guidelines",
(xix) IS:13935-1993 "Repair and Seismic Strengthening of Buildings - Guidelines"
For Protection of Landslide Hazard:
(xx) IS 14458 (Part 1): 1998 Guidelines for retaining wall for hill area: Part 1 Selection of type of wall.
(xxi) IS 14458 (Part 2): 1997 Guidelines for retaining wall for hill area: Part 2 Design of retaining/breast walls
(xxii) IS 14458 (Part 3): 1998 Guidelines for retaining wall for hill area: Part 3 Construction of dry stone walls
(xxiii) IS 14496 (Part 2): 1998 Guidelines for preparation of landslide – Hazard zonation maps in mountainous terrains: Part 2 Macro-zonation.
Note: Whenever an Indian Standard including those referred in the National Building Code or the National Building Code is referred, the latest revision of the same shall be followed except specific criteria, if any, mentioned above against that code.