The height or permissible elevation for the structure, requiring grant of NOC, shall be calculated based upon the International Civil Aviation Organization (ICAO) Annex 14 Obstacle Restriction and Removal, Annex 10 the Radio Communication, Navigation and Surveillance (CNS) aids and Doc 8168, Vol II defining the operational requirements for minimum altitudes of various segments of published or proposed instrument approach procedures.
This annexure–II defines various OLS surfaces, requirements w.r.t. CNS and PAN-OPS, procedure to be followed while applying and processing the NOC for height clearance.
Obstacle Limitation Surfaces (based on ICAO Annex 14 and DGCA India Civil Aviation Requirements (CARs) on Aerodrome Design and Operations) are as under:
1.1 Take-off climb surface-The dimensions of the take-off climb surface shall not be less than the dimensions specified in the table given below except that if a runway is meant for takeoff, a lesser length may be adopted for the takeoff climb surface where such lesser length would be consistent with procedural measures adopted to govern the outward flight of aeroplanes.
Table 2.1 -Dimensions and Slopes of Obstacle Limitation Surfaces
(Runways Meant for Take-Off)
Surface and dimension *
Code Number
(1)
1
2
3 or 4
(2)
(3)
(4)
TAKE OFF CLIMB
Length of inner edge
60 meters
80 meters
180 meters
Distance from runway end
30 meters
60 meters
60 meters
Divergence (each side)
10%
10%
12.5%
Final width
380 meters
580 meters
1200 meters 1800 meters**
Length
1600 meters
2500 meters
15000 meters
Slope
5%
4%
2%
* All dimensions are measured horizontally. **When the intended track includes changes of heading greater than 15 degree for operations conducted in IMC, VMC by night.
1.2Transitional Surface
1.2.1 The outer limit of the transitional surface is determined by its intersection with the plane containing inner horizontal surface and the slopes of transitional surfaces are as given below, namely:-
(i) Precision Approach Runway 14.3% (1:7)
(ii) Non Precision Runway 14.3% (1:7) for code 3 & 4
20% (1:5) for code 1 & 2
(iii) Non-Instrument Runway 14.3% (1:7) for code 3 & 4
20% (1:5) for code 1 & 2;
[PART II—SEC. 3(i)]
The slope of the transitional surface shall be measured in a vertical plane at right angles to the centre line of the runway;
1.2.2 The elevation of a point on a lower edge shall be –
(a) along the side of approach surface, equal to the elevation of approach surface at that point; and
(b) along the strip, equal to the elevation of nearest point on the centre line of the Runway or its extension;
1.5Conical Surface
1.5.1 The conical surface shall be projected upwards and outwards from the periphery of the Inner Horizontal Surface. The slope 5% (1:20) of the conical surface shall be measured in a vertical plane perpendicular to the Inner Horizontal Surface. The reference datum for Conical Surface shall be the aerodrome elevations (Refer to Appendix -B of Schedule VIII for illustration of the various surfaces including the conical surface).
Note: Where a part of Inner Horizontal Surface and conical surface lies below the approach/take-off climb surface, the permissible heights shall be the lowest of the applicable surfaces.
1.3Approach Surface
1.3.1 The approach surface shall be established for each runway strip in the direction of intended landing of the aeroplanes and the limits and slopes are given table below:
1.3.1.1 Instrument Runway
Inner Edge of Approach Surface:
Length of Inner edge - 150 meters for Code No. 1 and 2
300 meters for Code No. 3 and 4
Distance from runway threshold - 60 meters
Divergence -15% on either side
Length & Slope of Approach Surface: as given in table 2.2
Table 2.2Approach Surface Slope of Instrument Runway
Runway
Precision Approach Runway
Non Precision Approach Runway
Code No.
Aerodrome Reference Field Length (meter)
First Section Length & (Meter) Slope
Second Section Length (Meter) & Slope
First Section Length (Meter) & Slope
Second Section Length (Meter)& Slope
Horizontal Section (Meter)
1.
<800
30002.5%
12000**3%
25003.33%
--
--
2.
800<1200
30002.5%
12000**3.00%
25003.33%
--
--
3.
1200<1800
30002%
36002.5%
30002%
36002.5%
8400*
4.
1800 and Above
30002%
36002.5%
30002%
36002.5%
8400*
* Total length of approach surface for runway code number 3 and 4 with precision and non-precision shall be 15000 meters.
** Total length of approach surface for Precision approach Runway Code number 1 and 2 shall be 15000 meters.
1.3.1.2 Non-Instrument runway
Inner Edge of Approach Surface:
Length of Inner edge
60 meters for Code No. 1
80 meters for code No. 2
150 meters for Code No. 3 and 4
Distance from runway threshold
30 meters for code 1
¹Hkkx IIµ[k.M 3(i)º
Hkkjr dk jkti=k % vlk/kj.k
73
60 meters for code No. 2, 3 and 4
Divergence
-10% on either side
Length & Slope of Approach Surface: as given in table 2.3
Table 2.3Approach Surface Slope of Non-Instrument Runway
Runway
Length and slope of approach surface
Code No.
Aerodrome Reference Field Length (meter)
Length (Meter)
Section Slope
1.
<800
1600
5%
2.
800<1200
2500
4%
3.
1200<1800
3000
3.33%
4.
1800 & above
3000
2.5%
1.3.1.3 Aerodrome where there are more than one runway with over-lapping approach areas and associated surface, most stringent of the two would be the applicable criteria.
1.3.1.4 For determining the approach, the physical extremities of the runway shall only be considered. In case of displaced threshold the permissible height shall be calculated based on approach surface and transitional surface with respect to the runway extremity or displaced threshold whichever is more restrictive.
1.3.1.5 At Aerodromes, where the proposals for runway extension exist, the requisite surface shall be determined from the proposed extension as well as from the existing runway strip/associated clearway, as applicable and the lower of the two elevations shall be permitted. The elevation of the associated runway extremity/displaced threshold/proposed extension of runway shall be the datum for approach surface.
1.3.1.6 The slope of the approach surface shall be measured in a vertical plane containing the centerline of the runway.
1.4 Inner Horizontal Surface (IHS)
1.4.1 Dimensions and permissible heights of Inner Horizontal Surface are given in the table below:
Table 2.4Dimensions and Permissible Heights of Inner Horizontal Surface
Runway
Instrument
Non-Instrument
Code No.
Aerodrome Reference Field Length (meter)
Radius (Meter)
Height (Meter)
Radius (Meter)
Height above Aerodrome Elevation (Meter)
1.
<800
3500*
45
2000*
45
2.
800<1200
3500*
45
2000*
45
3.
1200<1800
4000**
45
4000**
45
4.
1800 and Above
4000**
45
4000**
45
*For runway code number 1 and 2, radius of IHS shall be measured from the Aerodrome Reference Point (ARP).
** For runway code number 3 and 4, radius of IHS shall be measured from the runway extremity.
1.4.1.1 The reference datum for Inner-Horizontal Surface shall be the aerodrome elevation as defined in clause (g) of the Explanation to this notification.
[PART II—SEC. 3(i)]
1.4.1.2 For Runway code 3 and 4, the Inner Horizontal Surface shall be a composite pattern, which consists of two circular areas centered at the two ends with a radius of 4000 meters. These areas shall be joined tangentially to form an elliptical shape as shown in Appendix-A of Schedule VIII.
1.4.1.3 Where it is required to protect two or more widely spaced long runways, a more complex pattern involving four or more circular areas are formed. These areas should be joined tangentially by straight lines and the Inner Horizontal Surface shall be defined by the external limits of the resulting pattern (Refer Appendix -A of Schedule VIII).
1.4.1.4 When two aerodromes are close to each other with overlapping circuits the Inner Horizontal Surface will be drawn as prescribed in para 1.4.1.3. The inner horizontal surface of these two aerodromes shall be joined tangentially to form one common Inner Horizontal Surface.
1.4.1.5 In case of common horizontal surface serving two aerodromes, the elevation of the Inner Horizontal Surface will be referenced to the lower of the two aerodromes.
1.6Outer Horizontal Surface (OHS)
1.6.1 The Outer Horizontal Surface shall extend to 15000 meters from the Aerodrome Reference Point for Aerodrome with runway code 3 and 4.
1.6.2 In case of Aerodrome with runway Code 2, the Outer Horizontal Surface shall extend to 14740 meters from Aerodrome Reference Point for Instrument runways and 13740 meters for Non-Instrument runways.
1.6.3 Where combined Outer Horizontal Surface is established for two Aerodromes, the Outer Horizontal Surface shall be centered on the Aerodrome Reference Point of the Aerodrome of higher category.
1.6.4 Outer Horizontal Surface for Aerodrome with runway code No.1 shall not be established.
1.6.5 The Outer Horizontal Surface, would be defined such that the Conical Surface may continue to be extended at 5% slope to a point wherein the permissible maximum height of *300 meters (above aerodrome elevation) is reached and thereafter this surface is maintained upto 15 kilometers from Aerodrome Reference Point. Construction(s) protruding above these surfaces shall normally not be permitted. Obstructions existing in the area should be marked or lighted.
*Note: In case of Defence Aerodromes, the permissible maximum height in conical and OHS shall be 150 meters above aerodrome elevation.
1.6.6 In order to avoid abrupt vertical changes in surfaces, the surfaces beyond the conical surfaces will slope laterally at 1:7 from edges of the approach and take off surfaces between the permissible heights of 150 meters to 300 meters (For illustration refer to Appendix -B of Schedule VIII).
1.6.7 The datum for Outer Horizontal Surface shall be the aerodrome elevation.
1.7 The Inner Approach, Inner Transitional and Balked Landing Surfaces (collectively referred as Obstacle Free Zone or OFZ):
1.7.1 Obstacles Free Zone shall be established for a runway equipped with precision approach (ILS) category I, II and III operations. The zone shall be kept free from fixed objects other air navigation aids, which must be near the runway, to perform their function, mounted on light weight frangible fixtures.
Note: Obstacles Free Zone for runway code No. 1 and 2 are not established.
The dimensions and slopes of the Obstacles free zone (Code 3 and 4) are given below.
2.8Advance Surface Movement Guidance and Control System (A-SMGCS):
No structure should be built on the relevant area of the airport surface which blocks the line of sight between any of the sensors of the Advance Surface Movement Guidance and Control System and the relevant operational area. In case there is an operational or safety/security requirement to add a structure on the airport surface which may obstruct the line of sight between Surface Movement Radar (SMR) antenna//sensors, AAI would augment the system to meet the Advance Surface Movement Guidance and control system operational requirement.
2.8.1 Surface Movement Radar (SMR)
Beyond the distance of 200 M. from SMR antenna, no object should protrude the line of sight to nearest point of designated coverage volume of said SMR.
2.8.2 Beyond the distance of 200 M from A-SMGCS Ref TX no object should protrude the line of site to nearest point of designated coverage volume of said ref TX and corridor between ref TX and MLAT of 5 Mx5 M.
¹Hkkx IIµ[k.M 3(i)º
Hkkjr dk jkti=k % vlk/kj.k
77
2.8.3 Beyond the distance of 200 M from A-SMGCS MLAT no object should protrude the line of designated coverage volume of said ref TX and a corridor between ref TX and MLAT of 5 Mx5 M.
2.6Air Route Surveillance Radar (ARSR)
Beyond 200 meters from particular Radar site the height of the permissible structures may be increased at the rate of 0.05 meter per meter, upto a point wherein the height of the permissible structure does not protrude above an angle of elevation of more than 0.5 degree at the antenna pedestal or an angle equal to antenna tilt angle set during last flight inspection whoever is higher. Beyond the above stated point no large object would be permitted to protrude above the line drawn at an angle of 0.5 degree from antenna pedestal or an angle equal to antenna tilt angle set during last flight inspection whichever is higher. Large object means the structure subtending azimuth angle of 0.4 degree or above at Radar antenna. In case of cluster of buildings wherein the gap between the two adjacent buildings sub tends an azimuth angle of less than 0.4 degree on the antenna pedestal, the entire cluster should be considered as one object (For illustration refer to Appendix -D of Schedule VIII).
Beyond 150m from particular ADS-B site, the height of the permissible structures does not protrude above the line drawn from a point 10% below the minimum sector altitude at the farthest point (from ADS-B site) or any other designated MSA at different distance in same sector whichever is closer to horizon, to the centre of the antenna pedestal of ADS-B.
1.7.1.2 The inner transitional surface Slope 33.3%
1.7.1.3 Balked Landing Surface Length of the Inner edge 120 meters Distance from Threshold 1800 meters Divergence 10% Slope 3.33 %
2 Protection of Service volume of various Communication, Navigation and Surveillance Facilities (based on ICAO Annex 10 Navigational Aids)
2.1 Very High Frequency Omni Range (VOR), Terminal Very High Frequency Omni Range (TVOR), and collocated Very High Frequency Omni Range Distance Measuring Equipment (VOR DME) - No structure (located beyond the area of 300M radius as specified in Annexure I) shall subtend a vertical angle greater than 1.5 degree at the centre of the Very High Frequency Omni Range counterpoise from the horizontal plane passing through the counterpoise.
2.2 Stand-alone Distance Measuring Equipment (DME) - No steel towers, power lines, metal buildings (located beyond the area of 150M radius as specified in Annexure I) shall protrude elevation angle of 3 degree measured from the base of Distance Measuring Equipment antenna.
2.3 Localizer
2.3.1 Within + 10 degrees azimuth in front of LLZ antenna, an object (located beyond the area specified in Annexure I) should not subtend an angle of elevation more than 0.75 degrees at the centre of antenna array.
2.3.2 Within + 10 degrees to + 35 degrees LLZ azimuth in front of antenna an object (located beyond the area specified in Annexure I) should not subtend an angle of elevation more than 1.1 degree.
2.3.3 Notwithstanding any thing in para 2.3.1 and 2.3.2, in all airports having/intended to have cat II and cat III ILS, all object in sector of + 18 degree for medium aperture antenna localizer and + 15 degree for wide aperture LLZ antenna, upto the distance of 1050M beyond threshold, to be analysed for their potential multipath effects on the performance of ILS.
Beyond areas specified in Annexure I and within + 8 degrees azimuth in front of the glide path antenna (in the direction of approach), a building/structure should not subtend an angle of elevation of more than 1.1 degree at antenna base.
2.5 Airport Surveillance Radar (ASR);
2.5.1 Wherever airport is served or proposed to be served by a single ASR, following criteria shall be applicable:
2.5.1.1 Beyond 500 meters from particular Radar site, the height of the permissible structures may be increased at the rate of 0.05 per meter, upto a point wherein the height of the permissible structure does not protrude above the line drawn from a point 10% below the minimum sector altitude at the farthest point (from Radar site) or any other designated MSA at different distance in same sector whichever is closer to horizon, to the centre of antenna pedestal, considering the Minimum Sector Altitude (MSA) in that particular sector. Beyond the above stated point no large object would be permitted to protrude above the line drawn from a point 10% below the minimum sector altitude at the farthest point (from Radar site) or any other designated MSA at different distance in same sector whichever is closer to horizon to the centre of antenna pedestal depending on the minimum Sector Altitude in that particular sector (For illustration refer to Appendix -C of Schedule VIII).
Note: Large object means the structure/s in isolation or collectively subtending azimuth angle of 0.4 degree or above at Radar antenna. In case of cluster of buildings wherein the gap between the two adjacent buildings sub tends an azimuth angle of less than 0.4 degree on the antenna pedestal, the entire cluster should be considered as one object.
[PART II—SEC. 3(i)]
2.5.2 Wherever airport is served or proposed to be served by Multiple Radars (more than one ASR), operational and integrated, following criteria shall be applicable:
2.5.2.1 In case only one ASR is installed and the proposed ASRs are yet to be operationalized and integrated, the existing ASR will be considered for height calculations as per the provisions of 2.5.1.
2.5.2.2 After multi radar system is operationalized and integrated, the maximum height permissible in the integrated system will be considered for calculation of height to the applicant. However, from the radar performance requirement point of view, the structures are to be examined, as follows, to ensure that there is no degradation of radar performance.
I. Within one kilometer of any ASR in the system, structures shall be examined from the respective radar as per para 2.5.1.
II. Between one and two kilometer, the metallic and large structures shall be examined from respective ASR as per para 2.5.1.
III. Structures which are Non -metallic and are not termed as large objects may be permitted to higher height as per IV below, subject to condition that other structure(s) in vicinity do not form cluster with the structure under examination.
IV. Objects beyond two kilometer from any one of the ASRs, highest permissible height among integrated & operational ASR sites shall be permitted as per para 2.5.1
Note: Above criterion will not be applicable for wind farms, high tension lines and electromagnetic source of interference.