xv) Communication and Navigational facilities include-
(a) Microwave Link which is a radio facility whereby mostly intelligence/data is carried to the Air Traffic Control Display site;
(b) Ultra High Frequency Link which is a radio relay facility operating in Ultra High Frequency Band;
(c) Beacons which are radio transmitters operating in the Medium Frequency band from 200 to 400 KHz radiating omni directionally in the horizontal plane and an aircraft equipped with a suitable cockpit instrument can get its location automatically with respect to this facility.
(d) Remote Receivers which are radio receiving stations (HF Band) installed at remote site away from factory or industrial areas to avoid interference link man-made static, etc.
Note: Location of Navigational Aids shall be determined as per the provisions of Annex-10 of International Civil Aviation Organization.
O SIN 0N A.C00 162 AG5SRD CR SION
THE GAZETTE OF INDIA : EXTRAORDINARY
[PART II—SEC. 3(i)]
Chapter 1Runway
1.1. Runway Strip: The Land area specified below shall be completely free from all obstacles as provided hereunder (Refer Appendix-1 of Schedule - I):-
1.1.1. The land comprising within the Runway strip of uniform width of 150 meters on either side of centerline which extends to 60 meters beyond each extremity of Runway, along the extended centerline of a Runway of code 3 or code 4, equipped with Instrument Approach Procedure.
1.1.2. The land comprising within the Runway strip of uniform width of 75 meters on either side of centerline which extends to 60 meters beyond each extremity of Runway, along extended centerline of the Runway of code 1or 2, equipped with Instrument Approach Procedure and for non-Instrument runway of code 3 or 4.
1.1.3. The land comprising within the Runway strip of uniform width of 40 meters on either side of centerline which extends to 60 meters beyond each extremity of Runway ,along extended centerline of the non-Instrument Runway of code 2.
1.1.4. The land comprising within the Runway strip of uniform width of 30 meters on either side of centerline which extends to 30 meters beyond each extremity of Runway, along extended centerline of the non-instrument runway of code 1.
1.2. Installation of Extra High Tension, High Tension lines shall not be permitted within 1500 metres of the Inner edge of the approach and take-off climb surface.
2. Frangibility Requirement:
2.1. Any equipment or installation required for air navigation purposes which must be located:
(a) On that portion of the runway strip within:
i) 75 meters of the Runway centerline where the Runway code is 3 or 4 or
ii) 45 meters of the Runway centerline where Runway code is 1 or 2; or
(b) on a runway end safety area, a taxiway strip or within the distances specified in CIVIL AVIATION REQUIREMENTS SECTION-4, SERIES 'B', PART I Aerodrome Design and Operations or
(c) on a clearway and which would endanger an aircraft in the air,
[PART II—SEC. 3(i)]
shall be frangible and mounted as low as possible.
2.2 Any equipment or installation required for air navigation purposes which must be located on or near a strip of precision approach Runway ILS category I, II or III and which-
(a) is situated on that portion of the runway strip within 77.5 meters of the Runway centerline where the code number is 4 and code letter is F; or
(b) is situated within 240 meters from the end of the runway strip and within-
(i) 60 meters of the extended runway centerline where Runway code is 3 or 4
(ii) 45 meters of the extended Runway centerline where Runway code is 1 or 2; or
(iii) penetrates the inner approach surface, the inner transitional surface or the balked landing surface,
shall be frangible and mounted as low as possible.
3. Communication, Navigation and Surveillance (CNS) Facilities
3.1. Very High Frequency Omni Range (VOR)/collocated Distance measuring Equipment (DME) and Very High Frequency Direction Finder (VHF DF): A land area within the 300 meters radius of the facility.
3.2. Localizer or LLZ (a component of ILS, providing azimuth guidance): the land area bounded by the following namely (Refer diagram at Appendix-L of Schedule VIII) :-
3.2.1. A line 300 meters in the direction of approach or nearest end of the runway, whichever is greater from localizer antenna and perpendicular to the runway.
3.2.2. A line 60 meters from the centerline of localizer antenna on both side and parallel to the runway.
3.2.3. A line containing centre of localizer antennas and perpendicular to the runway; and
3.2.4. Area within circle of 75 meters radius with centre at middle of the antenna system;
3.3. Glide Path (a component of ILS providing vertical guidance): the area bounded by the following, namely (Refer diagram at Appendix-K of Schedule VIII):-
3.3.1. A line 300 meters in the direction of approach from the glide path facility;
3.3.2. A line containing glide path antenna and perpendicular of runway;
3.3.3. Near edge of the runway from the glide path;
3.3.4. A line 30 meters in the directions away from the runway and parallel to it.
3.4. Locators or Markers Beacons: The land within a radius of 30 meters of the site of markers and locator beacons.
3.5. Airport Surveillance Radar (ASR): No structure will be permitted on the land above the level of 3 meters below the pedestal height up to the distance of 500 meters from Radar antenna.
3.6. Air Routes Surveillance Radar (ARSR): No structure will be permitted on the land above the level of 5 meters below the pedestal height up to the distance of 200 meters from Radar antenna.
3.7. Monopulse Secondary Surveillance Radar/ Secondary Surveillance Radar (MSSR/SSR): The distance and the height restriction shall be the same as in respect of the Airport Surveillance Radar or Air Routes Surveillance Radar, depending upon operational usage.
3.8. Microwave Link: On corridor of 30 meters on either side of the direct line of azimuth and 10 meters below from the direct line of sight in the vertical plane;
3.9. Ultra High Frequency (UHF) Link: On a corridor of 30 meters on either side of the direct line of the azimuth and 10 meters below from the direct line of sight in the vertical plane.
3.10. En-route Beacons: Land within a radius of 30 meters around the antenna.
3.11. Remote Receiver: Land within a radius of 1525 meters of the site.
¹Hkkx IIµ[k.M 3(i)º
Hkkjr dk jkti=k % vlk/kj.k
67
3.12. Stand-alone Distance Measuring Equipment / Automatic Dependence Surveillance – Broadcast (DME/ADS-B): No structure will be permitted on land above the level of 3 meters below the antenna base upto a distance of 150 meters from the antenna.
4. Definitions and Explanation.-
Some of the definitions of the terms used in the notifications have been provided below. For other terms, the CIVIL AVIATION REQUIREMENTS SECTION-4, SERIES 'B', PART I Aerodrome Design and Operations, ICAO annex 14, Annex 10 and Doc.8168 may be referred.
i) Runway: A defined rectangular area on a land aerodrome prepared for the landing and take-off of aircraft.
ii) Runway end safety area (RESA). An area symmetrical about the extended runway centre line and adjacent to the end of the strip primarily intended to reduce the risk of damage to an aeroplane undershooting or overrunning the runway.
iii) “Runway Strip” A defined area including the runway and stopway, if provided, intended:
a) to reduce the risk of damage to aircraft running off a runway; and
b) to protect aircraft flying over it during take-off or landing operations.
iv) “Runway Code”, means the Runway Code number specified in column (1), in relation to the Runway length specified in column (2), of the Table below:-
Table 1.1DIMENSION OF RUNWAY STRIP
RUNWAY
INSTRUMENT RUNWAY
NON-INSTRUMENT RUNWAY
Runway Code
Aerodrome Reference Field Length (ARFL) in (Meter)
Width Extending laterally on either side of Runway Centre Line (Meter)
Length beyond Runway End/Stop way (Meter)
Width Extending laterally on either side of Runway Centre Line (Meter)
Length beyond Runway End/Stop way (Meter)
(1)
(2)
(3)
(4)
(5)
(6)
1.
<800
75
60
30
30
2.
800<1200
75
60
40
60
3.
1200<1800
150
60
75
60
4.
1800 & above
150
60
75
60
v) “Approach funnel” in relation to (Refer Appendix-1 of Schedule -I):-
[PART II—SEC. 3(i)]
(a) Instrument Runway Code 3 and 4, means the area in the shape of an isosceles trapezium having the longer parallel side 4800 meters long (2400 meters on either side of the extended centerline of the runway) and smaller parallel side 300 meters long (150 meters on either side of the extended centerline of the runway), where the smaller and longer parallel sides are placed at a distance of 60 meters and 15060 meters respectively, from the end of the runway and at right angles to the extended centerline;
xiv) “Radar” includes-
(a) Airport Surveillance Radar (ASR) which is a radar facility serving an aerodrome to scan the air traffic within 50 to 60 nautical miles of the aerodrome;
(b) Air Routes Surveillance Radar (ARSR) or Secondary Surveillance Radar is a high power long-range radar covering a distance of 200 nautical miles approximately and it scans air traffic to a larger distance than Airport Surveillance Radar;
3.13. Airport Surface Detection Equipment (ASDE) or Surface Movement Radar (SMR): No structure will be permitted on the land above the level of 2 meters below the antenna base up to the distance of 200 meters from Radar antenna.
3.14. Advanced Surface Movement Guidance and Control Systems (A-SMGCS) Reference Transmitter: No structure will be permitted on the land above the level of 5 meters below the antenna base up to the distance of 200 meters from Radar antenna.
3.15. A-SMGCS Multi-Lateration (MLAT): No structure will be permitted on the land above the level of 2 meters below the antenna base up to the distance of 200 meters from Radar antenna.
3.16. Ground Based Augmentation System (GBAS) Reference Receiver: No structure will be permitted on land up to the distance of 100 meters from antenna.
3.17. Ground Based Augmentation System VHF Data Broadcast (GBAS VDB) station: No structure will be permitted on the land up to the distance of 300 meters from antenna
3.18. GBAS VDB monitoring station: No structure will be permitted on the land up to the distance of 300 meters from antenna.
3.19. Global Position System (GPS) Pseudolite Restriction: No GPS Pseudolite shall be used within the approach funnel of any runway or within the airport where GNSS/GBAS based operation has been planned/exist.
3.20. Global Navigation Satellite System (GNSS) repeater restriction: No GNSS repeater shall be installed/use in approach funnel and within the 500 meter from the basic strip where GNSS/GBAS based operation has been planned/exist.
(b) Instrument Runway (Precision) Code 1 and 2, means the area in the shape of an isosceles trapezium having the longer parallel side 4650 meters long (2325 meters on either side of the extended centerline of the runway) and smaller parallel side 150 meters long (75 meters on either side of extended centreline of the runway) where the smaller and longer parallel sides are placed at a distance of 60 meters and 15060 meters respectively, from the end of the runway and at right angles to the extended centerline;
(c) Instrument Runway (Non Precision) Code 1 and 2, means the area in the shape of an isosceles trapezium having the longer parallel side 900 meters long (450 meters on either side of the extended centerline of the runway) and smaller parallel side 150 meters long (75 meters on either side of the extended centerline of the runway), where the smaller and longer parallel sides are placed at a distance of 60 meters and 2560 meters respectively, from the end of the runway and at right angles to the extended centerline;
(d) Non-Instrument Runway Code 3 and 4, means the area in the shape of an isosceles trapezium having the longer parallel side 750 meters long (375 meters on either side of the extended centerline of the runway) and smaller parallel side 150 meters long (75 meters on either side of the extended centerline of the runway), where the smaller and longer parallel sides are placed at a distance of 60 meters and 3060 meters respectively, from the end of the runway and at right angles to the extended centerline;
(e) Non-Instrument Runway Code 2, means the area in the shape of an isosceles trapezium having the longer parallel side 580 meters long (290 meters on either side of the extended centerline of the runway) and smaller parallel side 80 meters (40 meters on either side of extended centreline of the runway) where the smaller and longer parallel sides are placed at a distance of 60 meters and 2560 meters respectively, from the end of the runway and at right angles to the extended centerline;
(f) Non- Instrument Runway Code 1 means the area in the shape of an isosceles trapezium having longer parallel side of 380 meters long (190 meters on either side of the extended centreline of the runway) and smaller parallel side 60 meters (30 meters on either side of extended centreline of the runway) where the smaller and longer parallel sides are placed at a distance of 30 meters and 1630 meters respectively from the end of the runway and at right angles to the extended centreline. The diagrams of runway strip and approach funnel of instrument runway code 1,2,3 and 4 and non– instrument runway code 3 and 4 have been shown in the Appendix-1 of Schedule-I ;
vi) “Instrument Runway” means a runway served by visual aids and non-visual aids providing directional guidance adequate for a straight in approach and intended for the operation of aircraft using instrument approach procedures;
vii) Non-Precision Approach Runway- means an instrument runway served by visual aids and a non-visual aid providing at least directional guidance adequate for a straight-in approach;
viii) Precision approach runway, category I – An instrument runway served by Instrument Landing System and/or MLS and visual aids intended for operations with a decision height not lower than 60 meters and either a visibility not less than 800 meters or a runway visual range not less than 550 meters.
ix) Precision Approach Runway, category II- An instrument runway served by Instrument Landing System and or MLS and visual aids intended for operations with a decision height not lower than 60 meters but not lower than 30 meters and a runway visual range not less than 350 meters.
x) Precision Approach Runway, Category III- An instrument runway served by Instrument Landing System (ILS) and/or MLS to and along with surface of the runway and –
(a) ILS CAT IIIA- intended for operations with a decision height lower than 30 meters, or no decision height and a runway visual range not less than 200 meters.
¹Hkkx IIµ[k.M 3(i)º
Hkkjr dk jkti=k % vlk/kj.k
69
(b) ILS CAT IIIB- intended for operations with a decision height lower than 15 meters, or no decision height and a runway visual range less than 200 meters but not less than 50 meters.
(c) ILS CAT IIIC- intended for operations with no decision height and no runway visual range limitations.
xi) “Non-Instrument Runway” means a runway intended for operations of the aircraft using visual approach procedure.
xii) “Very High Frequency Omni Range, Terminal Very High Frequency Omni Range, And Doppler Very High Frequency Omni Range” means the facilities operating in the Very High Frequency band of frequencies 112 to 118 MHz, radiate signals whereby an aircraft with the help of an instrument in its cockpit when tuned to the ground equipment frequency automatically gets its direction with respect to the facility and helps an aircraft to navigate on a predetermined course or home to an airport served by the facility.
xiii) “Instrument Landing System (ILS)” means the facility which serves to help an aircraft to make a safe landing on the runway in conditions of poor visibility and comprises of the following component facilities, namely:-
(a) Localizer facility which radiates Very High Frequency Signals which when picked up by an aircraft guide it onto the centerline of the runway in the horizontal plane and is normally situated about 305 meters from the runway end;
(b) Glide Path facility radiates Ultra High Frequency signals and is normally situated about 275 meters to 305 meters from the runway threshold and offset about 122 meters to 137 meters from the centerline of the runway and provides the glide angle information to a landing aircraft with the help of an instrument in the cockpit which when tuned to the glide path frequency indicates whether the aircraft is flying up or down or along the correct glide angle;
(c) Outer Marker or Outer Locator facility operating on 75 MHz in the Very High Frequency band is normally installed along the extended centerline of the runway at a distance between 3.5 and 6 nautical miles (1 nautical mile=1853 meters) and produces radiation pattern to indicate the landing aircraft, the pre-determined distance from the threshold along the Instrument Landing System glide path;