1.2.1 The outer limit of the transitional surface is determined by its intersection with the plane containing inner horizontal surface and the slopes of transitional surfaces are as given below, namely:-
(i) Precision Approach Runway 14.3% (1:7)
(ii) Non Precision Runway 14.3% (1:7) for code 3 & 4
20% (1:5) for code 1 & 2
(iii) Non-Instrument Runway 14.3% (1:7) for code 3 & 4
20% (1:5) for code 1 & 2;
[PART II—SEC. 3(i)]
The slope of the transitional surface shall be measured in a vertical plane at right angles to the centre line of the runway;
1.2.2 The elevation of a point on a lower edge shall be –
(a) along the side of approach surface, equal to the elevation of approach surface at that point; and
(b) along the strip, equal to the elevation of nearest point on the centre line of the Runway or its extension;
1.5Conical Surface
1.5.1 The conical surface shall be projected upwards and outwards from the periphery of the Inner Horizontal Surface. The slope 5% (1:20) of the conical surface shall be measured in a vertical plane perpendicular to the Inner Horizontal Surface. The reference datum for Conical Surface shall be the aerodrome elevations (Refer to Appendix -B of Schedule VIII for illustration of the various surfaces including the conical surface).
Note: Where a part of Inner Horizontal Surface and conical surface lies below the approach/take-off climb surface, the permissible heights shall be the lowest of the applicable surfaces.
1.3Approach Surface
1.3.1 The approach surface shall be established for each runway strip in the direction of intended landing of the aeroplanes and the limits and slopes are given table below:
1.3.1.1 Instrument Runway
Inner Edge of Approach Surface:
Length of Inner edge - 150 meters for Code No. 1 and 2
300 meters for Code No. 3 and 4
Distance from runway threshold - 60 meters
Divergence -15% on either side
Length & Slope of Approach Surface: as given in table 2.2
Table 2.2Approach Surface Slope of Instrument Runway
Runway
Precision Approach Runway
Non Precision Approach Runway
Code No.
Aerodrome Reference Field Length (meter)
First Section Length & (Meter) Slope
Second Section Length (Meter) & Slope
First Section Length (Meter) & Slope
Second Section Length (Meter)& Slope
Horizontal Section (Meter)
1.
<800
30002.5%
12000**3%
25003.33%
--
--
2.
800<1200
30002.5%
12000**3.00%
25003.33%
--
--
3.
1200<1800
30002%
36002.5%
30002%
36002.5%
8400*
4.
1800 and Above
30002%
36002.5%
30002%
36002.5%
8400*
* Total length of approach surface for runway code number 3 and 4 with precision and non-precision shall be 15000 meters.
** Total length of approach surface for Precision approach Runway Code number 1 and 2 shall be 15000 meters.
1.3.1.2 Non-Instrument runway
Inner Edge of Approach Surface:
Length of Inner edge
60 meters for Code No. 1
80 meters for code No. 2
150 meters for Code No. 3 and 4
Distance from runway threshold
30 meters for code 1
¹Hkkx IIµ[k.M 3(i)º
Hkkjr dk jkti=k % vlk/kj.k
73
60 meters for code No. 2, 3 and 4
Divergence
-10% on either side
Length & Slope of Approach Surface: as given in table 2.3
Table 2.3Approach Surface Slope of Non-Instrument Runway
Runway
Length and slope of approach surface
Code No.
Aerodrome Reference Field Length (meter)
Length (Meter)
Section Slope
1.
<800
1600
5%
2.
800<1200
2500
4%
3.
1200<1800
3000
3.33%
4.
1800 & above
3000
2.5%
1.3.1.3 Aerodrome where there are more than one runway with over-lapping approach areas and associated surface, most stringent of the two would be the applicable criteria.
1.3.1.4 For determining the approach, the physical extremities of the runway shall only be considered. In case of displaced threshold the permissible height shall be calculated based on approach surface and transitional surface with respect to the runway extremity or displaced threshold whichever is more restrictive.
1.3.1.5 At Aerodromes, where the proposals for runway extension exist, the requisite surface shall be determined from the proposed extension as well as from the existing runway strip/associated clearway, as applicable and the lower of the two elevations shall be permitted. The elevation of the associated runway extremity/displaced threshold/proposed extension of runway shall be the datum for approach surface.
1.3.1.6 The slope of the approach surface shall be measured in a vertical plane containing the centerline of the runway.
1.4 Inner Horizontal Surface (IHS)
1.4.1 Dimensions and permissible heights of Inner Horizontal Surface are given in the table below:
Table 2.4Dimensions and Permissible Heights of Inner Horizontal Surface
Runway
Instrument
Non-Instrument
Code No.
Aerodrome Reference Field Length (meter)
Radius (Meter)
Height (Meter)
Radius (Meter)
Height above Aerodrome Elevation (Meter)
1.
<800
3500*
45
2000*
45
2.
800<1200
3500*
45
2000*
45
3.
1200<1800
4000**
45
4000**
45
4.
1800 and Above
4000**
45
4000**
45
*For runway code number 1 and 2, radius of IHS shall be measured from the Aerodrome Reference Point (ARP).
** For runway code number 3 and 4, radius of IHS shall be measured from the runway extremity.
1.4.1.1 The reference datum for Inner-Horizontal Surface shall be the aerodrome elevation as defined in clause (g) of the Explanation to this notification.
[PART II—SEC. 3(i)]
1.4.1.2 For Runway code 3 and 4, the Inner Horizontal Surface shall be a composite pattern, which consists of two circular areas centered at the two ends with a radius of 4000 meters. These areas shall be joined tangentially to form an elliptical shape as shown in Appendix-A of Schedule VIII.
1.4.1.3 Where it is required to protect two or more widely spaced long runways, a more complex pattern involving four or more circular areas are formed. These areas should be joined tangentially by straight lines and the Inner Horizontal Surface shall be defined by the external limits of the resulting pattern (Refer Appendix -A of Schedule VIII).
1.4.1.4 When two aerodromes are close to each other with overlapping circuits the Inner Horizontal Surface will be drawn as prescribed in para 1.4.1.3. The inner horizontal surface of these two aerodromes shall be joined tangentially to form one common Inner Horizontal Surface.
1.4.1.5 In case of common horizontal surface serving two aerodromes, the elevation of the Inner Horizontal Surface will be referenced to the lower of the two aerodromes.
Schedule IIPurpose:
The height or permissible elevation for the structure, requiring grant of NOC, shall be calculated based upon the International Civil Aviation Organization (ICAO) Annex 14 Obstacle Restriction and Removal, Annex 10 the Radio Communication, Navigation and Surveillance (CNS) aids and Doc 8168, Vol II defining the operational requirements for minimum altitudes of various segments of published or proposed instrument approach procedures.
This annexure–II defines various OLS surfaces, requirements w.r.t. CNS and PAN-OPS, procedure to be followed while applying and processing the NOC for height clearance.
Obstacle Limitation Surfaces (based on ICAO Annex 14 and DGCA India Civil Aviation Requirements (CARs) on Aerodrome Design and Operations) are as under:
1.1 Take-off climb surface-The dimensions of the take-off climb surface shall not be less than the dimensions specified in the table given below except that if a runway is meant for takeoff, a lesser length may be adopted for the takeoff climb surface where such lesser length would be consistent with procedural measures adopted to govern the outward flight of aeroplanes.
Table 2.1 -Dimensions and Slopes of Obstacle Limitation Surfaces
(Runways Meant for Take-Off)
Surface and dimension *
Code Number
(1)
1
2
3 or 4
(2)
(3)
(4)
TAKE OFF CLIMB
Length of inner edge
60 meters
80 meters
180 meters
Distance from runway end
30 meters
60 meters
60 meters
Divergence (each side)
10%
10%
12.5%
Final width
380 meters
580 meters
1200 meters 1800 meters**
Length
1600 meters
2500 meters
15000 meters
Slope
5%
4%
2%
* All dimensions are measured horizontally. **When the intended track includes changes of heading greater than 15 degree for operations conducted in IMC, VMC by night.